WeatherHawk WM-350 WindMate Multi-function Weather Meter - Manual (Page 4)

Screen Set Menu
To navigate the Screen Set Menu press the
Set/EL Key to go to the next screen and set as
shown:
To turn on or off a mode, press the View Key.
To save and exit the screen set menu press the
Mode Key, this will take you to the Memory
Settings.
Memory Settings
In the Memory Settings, you can:
Set Storage Rate, which changes the intervals
for recording and saving data
Turn on or off the Memory Over-write option
Clear Memory and view the Memory Status
Deactivate Auto Shut-off & Storm Alarm
Change Display Contrast.
To navigate the Memory Setting press the
Set/EL Key.
Storage Rate has the following
fixed options: 5 min, 10 min, 20
min, 30 min, 1 hr, 2 hr, 6 hr, and
12 hr. The default setting is 1 hr.
To select Storage Rate press the View Key.
Note: The bar graph always shows 48
increments. Ex. If you keep the 1 hr increment,
the bar graph shows a 48-hr history. If you
change to a 2-hr increment, you will have a 96-
hr history; 12-hr increment will give you 2
measurements per day for 24 days.
Memory Overwrite option can be turned on or
off. If this option is turned on, the unit will
automatically over-write old data after the
memory is full. Press the View Key to turn on or
off this option.
Clear All Logs option allows you to clear and
erase all old data, so you have a new history. To
select yes or no, press the View Key. The
selected option will take effect after pressing
Mode Key. You can also reset the Min/Max/Avg
choices for each function.
Memory Status. The amount
of data saved and unused
memory is measured in hours.
The Memory Status shows
you the amount of saved data & unused memory
as shown on the right. Press Mode Key to save.
This will take you to Auto-Shutoff option.
Deactivate Auto Shut-Off
The Auto Shut-Off feature helps preserve the
battery. With Auto Shutoff deactivated, the unit
will work until the memory is full. This feature
can be switched on or off by pressing the View
Key. To save settings and go to the next option
press the Mode Key.
Deactivate Storm Warning Alarm
To turn off the alarm (or reactivate), press the
View Key. To save and go to the next option,
press the Mode Key.
Change Display Contrast
Display text contrast goes from light (0) to dark
(15). The unit is preset to 8. To darken or
lighten, press the View Key. To save and exit to
Time mode press the Mode Key.
Replacing the Battery
Because this unit has a capacitor, it will hold
your settings during a battery change, as long as
it is within several minutes. The unit uses a CR
2032 Lithium battery. Turn the unit to access the
battery cover. Turn it as indicated by the arrow
using a coin. Insert the battery into the unit. The
printed side faces you. Close the battery door
using the coin.
Replacing the Wind Impeller
Contact WeatherHawk or
your dealer for parts to
replace the impeller.
Impeller Replacement:
Turn the unit so the back
faces you. Remove the
screw cover plug & loosen
the screw. Turn the wind impeller clockwise and
pull it from the unit. Insert the new wind impeller.
Turn it in a counter-clockwise direction and
tighten the screw. Replace the screw cover
plug.
* * * * * * * * *
The WindMate
® 350 has a 2-year warranty.
Please keep your invoice or receipt.
Contact WeatherHawk for questions or service.
435-750-1840, M-F, 8:00 – 5:00, USA Mountain
Standard Time, www.weatherhawk.com
Additional manuals and instrument
specifications can be accessed from our website
at www.weatherhawk.com.
ACCURACY:
Wind speed +/- 3%
Compass +/- 2°
Wind Direction +/- 2°
Temperature +/- 1.8° F; 1° C
Relative Humidity +/- 3%
Wet Bulb & Dewpoint +/- 3.6° F; 2° C
Barometer +/- .05 inHg; 1.5 hPa
Altimeter +/- 50 Ft; 15 m
Density Altitude +/- 246 Ft; 75 m
Screw