Kenwood KMR-M308BT - Manual (Page 17)

17 ENGLISH |
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [AUDIO CONTROL], then press the
knob.
3 Turn the volume knob to make a selection (see the following table),
then press the knob.
Repeat step 3 until the desired item is selected or activated.
4 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [AUDIO CONTROL].
2 Press J / K to make a selection, then press ENT IW.
To return to the previous setting item or hierarchy, press .
Default: XX
SUB-W LEVEL –15 to +15 (0): Adjusts the subwoofer output level.
BASS LEVEL –8 to +8 (+6):
Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you
want to adjust.)
MID LEVEL –8 to +8 (+5):
TRE LEVEL –8 to +8 (0):
PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/ NATURAL/
USER: Selects a preset equalizer suitable to the music genre. (Select
[USER] to use the customized bass, middle, and treble settings.)
[DRIVE EQ] is a preset equalizer that reduces noise from the road.
BASS BOOST LV1 / LV2/ LV3: Selects your preferred bass boost level. ; OFF: Cancels.
LOUDNESS LV1/ LV2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.
LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/ 160 Hz
are sent to the subwoofer.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
FADER R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET
(Default: 0) –8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volume
adjustment level of each source. (Before adjustment, select the source
you want to adjust.)
SOUND RECNSTR
(Sound
reconstruction) ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression. ; OFF: Cancels.
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
EN_KMM_BT308U_KN_2.indd 17 EN_KMM_BT308U_KN_2.indd 17 8/11/2013 3:46:56 PM 8/11/2013 3:46:56 PM