Teledex CL Series - Manual (Page 10)

AUTO DIAL KEYS
The CL1200 series has either five (5) or ten (10) programmable
guest service (auto dial) keys, depending on the model you own.
These keys can be programmed to automatically dial telephone
numbers, or to activate telephone system features. To program the
auto dial keys (programming can only be done from base unit):
1. With the faceplate removed, press the recessed STORE key.
2. Enter the desired telephone number (up to 15 digits in
length) to be stored.
3. Press the STORE key again.
4. Press the auto dial key where the number is to be stored.
Programming is now completed for that auto dial key.
To program additional keys, repeat this process.
RECEIVING A CALL
An audible ring and flickering red LED indicate an incoming call.
To answer the call using the handset while it is not on the base:
1. Pick up the handset.
2. Press the line key. The handset will go“off-hook” answering
the ringing line.
3. To end the call, place the handset in the base unit cradle, or
press the lit line key on the handset.
To answer the call using the handset while it is resting on the base:
1. Pick up the handset from the base. The phone will
automatically connect to the line.
2. To end the call, replace the handset in the base unit cradle,
or press the lit line key on the handset.
To answer the call using the speakerphone:
1. Press the line key for the ringing line. The speakerphone will
go “off-hook”, answering the line.
2. Or, press the SPKR key. The speakerphone will go “off-hook”,
answering the line.
3. To end the call, press the SPKR key again.
PLACING A CALL
Using the handset:
1. Pick up the handset and press the LINE key. Listen for dial
tone and dial the desired number.
2. After the call is complete, press the LINE key again to end
the call.
Using the speakerphone:
1. Press the LINE key, or press SPKR.
2. Listen for dial tone, and dial the desired number, or press an
auto dial key to dial a preprogrammed number.
3. After the call is complete, press the SPKR key to end call.
REDIAL
The CL1200 series can automatically redial the last number dialed.
On the handset, press the REDIAL key to redial the last number.
USING THE HOLD KEY
The HOLD key places the call on hold locally at the cordless
telephone.
To place a call on hold:
1. With a call active, press the red HOLD key on either the
handset or base unit.
2. The red line LED will slowly blink, indicating the call is on hold.
To remove a call from hold:
1. Press the line key of the call on hold. This will remove the
call from hold, making the call active again.
2. The red line LED will return to steady illumination, indicating
the line is active.
To change phones after placing a call on hold:
1. Place the call on hold as above.
2. Pick up the call at another telephone that is on the same
line. The telephone will activate the line and remove the hold
at the original telephone.
TO MUTE THE SPEAKERPHONE
1. Press the MUTE key on the base unit. The red LED above
the MUTE key will illuminate. The party on the other end
will not be able to hear you when the MUTE LED is lit.
2. Press the MUTE key again to turn off the mute feature.
The MUTE LED will go out.
CONVERTING FROM DESK TO WALL MOUNT
The CL1200 series can be adapted for wall mounting applications.
The conversion is easiest to make when the handset and cords
are not connected.
1. Located on the handset cradle, above the speaker grill, is the
wall/desk mount clip. Remove this clip by firmly pushing it
upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that the protruding edge is
towards the top of the phone and replace it in its slot. This edge
will hold the handset when the phone is mounted on the wall.
3. Turn the telephone over so the bottom is up, facing you.
Place it on a non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket. Firmly push back
and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180º degrees clockwise, so that
the mounting eyelet on the bracket is facing in the same
direction as the other mounting eyelet located on the
bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets
into the mounting bracket slots (located near the middle of
the telephone). Then firmly push down to insert the retaining
tabs on the opposite side of the mounting bracket.
7. Connect a 15-foot RJ-45 cord into the LINE jack on the back
of the phone.
8. Turn the telephone over, and slide the telephone down onto
the mounting posts of the wall bracket. Ensure that both
eyelets line up with the mounting posts.
REQUIREMENTS OF PART 68 - FCC RULES
This device has been granted a registration number by the Federal
Communications Commission, under Part 68 rules and regulations for
direct connection to the telephone lines. In order to comply with these
FCC rules, the following instructions must be carefully read and applicable
portions followed completely:
1. Direct connection to the telephone lines may be made only through the
standard modular cord furnished, to the utility installed jack. No connection
may be made to party or coin phone lines. On the bottom of the phone is
a label that contains among other information, the FCC Registration
Number and the Ringer Equivalence number (REN) for this equipment. If
requested this information must be provided to the telephone company.
The USOC Jack for this equipment is RJ11C.
2. The telephone company, under certain circumstances, may temporarily
discontinue and make changes in facilities and services which may affect
the operation of the users' equipment: however, the user shall be given
adequate notice in writing to allow the user to maintain uninterrupted
service.
3. In certain circumstances, it may be necessary for the telephone company
to request information from you concerning the equipment which you
have connected to your telephone line. Upon request of the telephone
company, provide the FCC registration number and the ringer equivalence
number of the equipment which is connected to your line; this information
will be found on the device.
4. If any of your telephone equipment is not operating properly, you should
immediately remove it from the telephone line. It may cause harm to the
telephone network.
5. If the telephone company notes a problem, they may temporarily
discontinue service. When practical, they will notify you in advance
disconnection. If advance notice is not feasible, the telephone company
must; promptly notify you of such temporary discontinuance; afford the
opportunity to correct the condition; inform you of your rights to bring a
complaint to the FCC under their rules.
6. Repairs to the device may be made only by the manufacturer or an
authorized service agency. This applies at any time during and after
warranty. If unauthorized repair is performed, registration, connection to the
telephone lines and remainder of warranty period all become null and void.
7. This equipment is hearing aid compatible.
8. This telephone must be connected behind a PBX.
REQUIREMENTS OF PART 15 - FCC RULES
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful inter-
ference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction, may cause harmful interference to radio com-
munications. However, there is not a guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Move the tele-
phone away from the receiver; Consult the dealer or an experienced
radio/TV technician for help. Any changes made by the user not approved
by the manufacturer can void the user's authority to operate the telephone.
FCC RF EXPOSURE INFORMATION
In August 1996, the Federal Communications Commission (FCC) of the
United States, with its action in Report and Order FCC 96-326, adopted
an updated safety standard for human exposure to radio frequency
electromagnetic energy emitted by FCC-regulated transmitters. Those
guidelines are consistent with the safety standard previously set by both
US and international standards bodies. This phone has been tested to
and complies with the FCC guidelines and these international standards.
INDUSTRY OF CANADA REQUIREMENTS
NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets certain telecommunica-
tions network protective operational and safety requirements as pre-
scribed in the appropriate Terminal Equipment Technical Requirements
documents. The department does not guarantee the equipment will
operate to the users satisfaction. Before installing this equipment, users
should ensure that it is permissible to be connected to the facilities of
the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not
prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment. Users should
ensure for their own protection that the electrical ground connections of
the power utility, telephone lines, and internal metallic water pipe sys-
tems, if present, are connected together. This precaution may be particu-
larly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority or electrician, as
appropriate.
The Ringer Equivalence Number (REN) of this device is 0.7B.
Notice: The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed 5. This telephone connects to the telephone
network under the connecting arrangement code CA11A.