Campbell Scientific CR200/CR200X-series Dataloggers User Manual

Operator’s manual

Advertising

OPERATOR’S

MANUAL

CR200/CR200X Series

Dataloggers

Revision: 1/14

C o p y r i g h t © 2 0 0 0 - 2 0 1 4

C a m p b e l l S c i e n t i f i c , I n c .

Advertising

Table of contents

Document Outline

Revision and Copyright Information
Warranty
Assistance
Table of Contents
Section 1. Introduction
- 1.1 CR200(X) series Datalogger Models
Section 2. Quickstart Tutorial
- 2.1 Primer - CR200(X) Data Acquisition
- 2.2 Hands-on Exercise - Measuring Temperature
Section 3. Overview
- 3.1 CR200(X) Overview
- 3.2 PC Support Software
- 3.3 Specifications
Section 4. Sensor Support
- 4.1 Powering Sensors
- 4.2 Voltage Measurement
- 4.3 Bridge Resistance Measurements
  - 4.3.1 Measurements Requiring AC Excitation
- 4.4 Pulse Count Measurement
  - 4.4.1 Pulse input Channels
    - 4.4.1.1 Pulse Input (P_SW)
    - 4.4.1.2 Low-Level AC (P_LL)
  - 4.4.2 Pulse Input on Digital I/O Channels C1–C2
- 4.5 Period Averaging Measurements
- 4.6 SDI-12 Recording
- 4.7 Cabling Effects on Measurements
Section 5. Measurement and Control Peripherals
- 5.1 Control Output
  - 5.1.1 Binary Control
- 5.2 Other Peripherals
  - 5.2.1 TIMs
Section 6. CR200(X) Power Supply
- 6.1 Power Requirement
- 6.2 Calculating Power Consumption
- 6.3 Power Supplies
  - 6.3.1 Battery Connection
Section 7. Grounding
- 7.1 ESD Protection
  - 7.1.1 Lightning Protection
- 7.2 Single-Ended Measurement Reference
Section 8. CR200(X) Configuration
- 8.1 DevConfig
- 8.2 Sending the Operating System
  - 8.2.1 Sending OS with DevConfig
- 8.3 Settings
Section 9. Programming
- 9.1 Inserting Comments into Program
- 9.2 Sending Programs
- 9.3 Writing Programs
  - 9.3.1 Short Cut Editor and Program Generator
  - 9.3.2 CRBASIC Editor
- 9.4 Numerical Formats
- 9.5 Structure
- 9.6 Declarations I - Single-line Declarations
- 9.7 Declarations II - Declared Sequences
  - 9.7.1 Data Tables
  - 9.7.2 Subroutines
- 9.8 Program Execution Timing
- 9.9 Instructions
- 9.10 Expressions
- 9.11 Program Access to Data Tables
Section 10. CRBASIC Programming Instructions
- 10.1 Program Declarations
  - 10.1.1 Variable Declarations & Modifiers
  - 10.1.2 Constant Declarations
- 10.2 Data Table Declarations
  - 10.2.1 Data Table Modifiers
  - 10.2.2 Data Storage Output Processing
    - 10.2.2.1 Single-Source
    - 10.2.2.2 Multiple-Source
- 10.3 Single Execution at Compile
- 10.4 Program Control Instructions
  - 10.4.1 Common Controls
- 10.5 Measurement Instructions
- 10.6 Processing and Math Instructions
- 10.7 Clock Functions
- 10.8 Serial Input / Output
- 10.9 Peer-to-Peer PakBus Communications
- 10.10 Data Table Access and Management
- 10.11 SCADA
- 10.12 Satellite Systems Programming
  - 10.12.1 GOES
Section 11. Programming Resource Library
- 11.1 Remote Sensor Interface
- 11.2 Radio Power Minimization
- 11.3 Multiple Switch Closure Measurements
- 11.4 SDI-12 Sensor Support
- 11.5 Wind Vector
  - 11.5.1 OutputOpt Parameters
  - 11.5.2 Wind Vector Processing
    - 11.5.2.1 Measured Raw Data
    - 11.5.2.2 Calculations
      - 11.5.2.2.1 Input Sample Vectors
      - 11.5.2.2.2 Mean Wind Vector
- 11.6 TrigVar and DisableVar - Controlling Data Output and Output Processing
- 11.7 Multiple Data Intervals in Data Tables
Section 12. Memory and Data Storage
- 12.1 Data Storage
  - 12.1.1 Data Table Storage
- 12.2 Memory Conservation
- 12.3 Memory Reset
Section 13. Telecommunications and Data Retrieval
- 13.1 Hardware and Carrier Signal
- 13.2 Protocols
- 13.3 Initiating Telecommunications
- 13.4 Data Retrieval
  - 13.4.1 Via Telecommunications
  - 13.4.2 Data Format on Computer
Section 14. PakBus Overview
- 14.1 PakBus Addresses
- 14.2 Nodes: Leaf Nodes and Routers
- 14.3 Router and Leaf Node Configuration
- 14.4 Linking Nodes: Neighbor Discovery
- 14.5 Troubleshooting
- 14.6 LoggerNet Device Map Configuration
Section 15. Alternate Telecoms Resource Library
- 15.1 Modbus
Section 16. Support Software
- 16.1 Short Cut
- 16.2 PC200W
- 16.3 Visual Weather
- 16.4 PC400
- 16.5 RTDAQ
- 16.6 LoggerNet Suite
- 16.7 PDA Software
- 16.8 Network Planner
Section 17. Care and Maintenance
- 17.1 Temperature Range
- 17.2 Moisture Protection
- 17.3 Enclosures
- 17.4 Replacing the Internal Battery
Section 18. Troubleshooting
- 18.1 Programming
- 18.2 Communications
  - 18.2.1 RS-232
  - 18.2.2 Communicating with Multiple PC Programs
- 18.3 Power Supply
Appendix A. Glossary
- A.1 Terms
- A.2 Concepts
  - A.2.1 Accuracy, Precision, and Resolution
Appendix B. Status Table and Settings
Appendix C. Serial Port Pin Outs
- C.1 RS-232 Communications Port
  - C.1.1 Pin-Out
Appendix D. ASCII / ANSI Table
Appendix E. Antenna Usage and Compliance
- E.1 Use of Antenna with CR200(X)
- E.2 Part 15 FCC Compliance Warning
  - E.2.1 Use of Approved Antennas
Index
Campbell Scientific Companies

Popular Brands

Popular manuals