Samsung UN22C4000PDXZA User Manual
Quick setup guide, Releas e lock loc eleas e se loc rele a, Step 1
Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12
AM EST.
To register this product, visit: www.samsung.com/
register.
STOP
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the LED TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the LED TV placed down, it may lean to one side.
UN19C4000, UN22C4000, UN22C4010
1
Insert the stand body into the stand
base.
2
Screw the stand base to the stand
body.
3
Slide the TV onto the stand
body.
RELEAS
E
LOCK
LOC
ELEAS
E
SE
LOC
RELE
A
UN26C4000
1
Connect the Guide Stand to the
Stand using four screws (M4 X
L12) as shown
s
s
s
s
s
2
With your TV upright, connect the
TV to the Stand as shown.
3
Fasten three screws (M4 X L8) at
position 1, and then fasten three
screws (M4 X L8) at position 2.
s
s
s
s
s
1
s
s
s
s
s
2
Step 4
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the
ENTER
E button.
To skip a screen, press the
MENU
button. To turn on your TV, press the
POWER
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control, select
the language for the On Screen
Display (OSD), and then press the
ENTER
E button.
2
Select Home Use, and then
press the
ENTER
E button. If
you select Store Demo, the TV
will reset your picture and audio
settings every 30 minutes.
3
Select Antenna Source to
memorize. If Antenna Source is
Cable or Auto, you must select
your cable system type. After
selecting source, select Search; then press the
ENTER
E button on your
remote.
✎
Most cable systems are Standard (STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
5
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don’t, or
if you have a cable or satellite box. When done, press the
ENTER
E button.
✎
If you select Manual, the clock setting screen appears.
6
Select the daylight savings time setting: Off or On, and then press the
ENTER
E button.
7
Select the time zone in which you live, and then press the
ENTER
E button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The Enjoy your TV. screen appears. Then press the
ENTER
E button.
If You Want to Rerun Plug & Play
1. Press the
SOURCE
button on your remote, then select TV mode.
2. Press the
MENU
button on your remote to display the menu.
3. Press the
▲ or ▼ button to select Setup, and then press the
ENTER
E
button.
4. Press
ENTER
E again to select Plug & Play.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Using an EX-Link Cable Connection
Available Devices: External devices that support EX-Link.
OPTICAL
AUDIO IN
OPTICAL
Analog Audio connection
Digital Audio connection
Amplifier / DVD home theater
Using a Headphone
Using an Optical Cable
U Move E Enter
Select Language of the OSD.
Menu Language
:
Plug & Play
English
Español
Français
Step 3
: Connect External Devices
Connecting an AV device (DVD / Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to
connect your TV to an external A/V
device.
We recommend using HDMI for the
highest picture quality.
AUDIO OUT
VIDEO OUT
AUDIO OUT
COMPONENT OUT
AUDIO OUT
DVI OUT
HDMI OUT
Using a HDMI to DVI Cable
HD connection (up to 1080p)
Very Good Connection
Device
Using a Component Cable
Good Connection
Component connection (up to 1080p)
Best Connection
HD connection (up to 1080p)
Using an HDMI Cable
Lowest Quality Connection
Using an Audio/Video Cable
Audio/Video connection (480i only)
Analog Audio connection
Using an Audio Cable
Digital Audio connection
Using an Optical Cable
Digital Audio System
Digital Audio System
DVD / Blu-ray player
Device
Audio Cable
(Not Supplied)
Component Cable
(Not Supplied)
HDMI to DVI Cable (Not Supplied)
Audio Cable (Not Supplied)
Video Cable (Not Supplied)
Video Cable (Not Supplied)
HDMI Cable (Not Supplied)
Optical Cable (Not Supplied)
Optical Cable (Not Supplied)
Audio Cable (Not Supplied)
headphone
Audio Cable
(Not Supplied)
Audio Cable
(Not Supplied)
D-Sub Cable (Not Supplied)
HDMI to DVI Cable
(Not Supplied)
DVI OUT
AUDIO OUT
AUDIO OUT
PC OUT
HD connection
Using a HDMI to DVI Cable
Using a D-Sub Cable
Device
EX-LINK
: Connector for service only.
DVD / Blu-ray player
/ HD Cable Box / HD
Satellite receiver (STB)
DVD / Blu-ray player / Cable Box / Satellite receiver / VCR
DVD / Blu-ray player / Cable Box / Satellite
receiver / VCR
Step 2
: Connect Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
or
Antenna Cable (Not Supplied)
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
U Move E Enter
Anrenna Source
:
Digital Cable System
:
Analog Cable System
:
Air
Cable
Auto
Search
Plug & Play
Top view
Guide Stand
Screws (M4 X L12)
Stand
Rear
Rear
Front
[QSG]BN68-02628A-01Eng.indd 1
2010-09-03 오후 6:46:05