English – Samsung SCW-230E User Manual

Page 3

Advertising
background image

System Requirements

Installing the CD-R/RW Drive

Installing the Device Driver

4

5

Before you install the CD-R/RW drive, we strongly recommend that you make certain
that your set-up meets the system requirements listed below.

Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close
button is on the right.

1

Turn OFF your computer. Remember to verify the
configuration jumper on the rear of the CD-R/RW drive.

To install the drive, proceed as follows.

2

Remove the cover of your PC(main unit of the computer).

3

Remove the blank cover panel of the 5.25 inch unit in
which the CD-R/RW drive is to be installed.

4

Connect the CD-R/RW drive to the IDE interface and
power cables located inside your computer.

☛

Connectors are keyed so it is impossible to put them in

☛

an incorrect position. Do not force the connectors, if they

☛

do not seem to fit.

5

Install the CD-R/RW drive into the unit and secure it with
mounting screws (recommended standard M3x6).

☛ ◆

Depending on your PC model, you may need to attach

☛ ◆

guide rails to the drive, so that the drive is held firmly in place.

☛ ◆

On the ground that the guide rails are parts of the computer,

☛ ◆

if you don’t have these, please purchase separately.

☛

◆

If you use screws that are longer than the recommended

☛ ◆

standard, you may damage the drive.

6

Put the cover back on your PC.

Item

Description

Type of computer

Pentium 75MHz(or higher) with an IDE interface

16MB RAM(or higher)

528MB higher(Transfer Rate 800KB/sec higher Access,
Time 20m/sec Lower)

5.0(or higher)
TIP:For MS-DOS, The CD-R/RW drive can only Read a
disc without Premaster Software

RAM

Hard drive

MS-DOS

Microsoft

®

Windows 95

®

or Windows NT 4.0

®

TIP:For Windows NT

®

, we recommend Service Pack2,

Version 4.00.1381.

Windows

You can install the device driver for DOS or for Windows.

TIP : You can use the CD-R/RW drive to only read a disc in DOS/Windows 3.1.

1

Turn on your computer and wait for it to boot.

7

Reboot your system.
Result:

◆

The computer restarts

◆

Both the device driver and MSCDEX are loaded.

6

When the Setup Completed screen is displayed, remove the installation
floppy disk from the drive.

2

Insert the driver disk into a floppy disk drive (usually the A drive).

4

Run the CDSETUP program:

5

To...

Then enter...

Confirm the installation Y

Exit without installing N

Result:

If you answer Y(Yes), the installation program automatically

◆

Creates a SAMSUNG directory on your hard disk

◆

Copies the required softwares (mscdex.exe and sscdrom.sys)

◆

Modifies the CONFIG.SYS and AUTOEXEC.BAT files

3

If you are a...

Then...

DOS user

Windows user
3.1

Windows 95 user
/NT 4.0

◆

Type a: at the DOS prompt.

◆

Press the RETURN key.

◆

Access the File Manager.

◆

Click on the A icon.

◆

When you are in Windows 95, it is not

◆

necessary to install Device Driver.

◆

Whereas, when you are in Dos Mode of

◆

Windows 95, then install as follows.

◆

Click on MY COMPUTER icon.

◆

Click on the A icon.

If you are a...

Then...

DOS user

Windows user
3.1

◆

Type CDSETUP after the a: prompt.

◆

Press RETURN.

Double-click CDSETUP.EXE from the
Windows File Manager.

English

SCW-230(E/G/F/S) 3/31/00 2:35 PM Page 3

Advertising