Swiftech APOGEE - Manual (Page 2)

Copyright Swiftech 2005 – All rights reserved – Last revision date: 6-12-06 – One or more Patents Pending
Rouchon Industries, Inc., dba Swiftech – 1703 E. 28
th Street, Signal Hill, CA 90755 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:
[email protected] – URL: http://www.swiftnets.com - Information subject to change without notice
Packing List
COMPONENT ID COMPONENT DESCRIPTION QTY USAGE
BHSC006C0-007SS 6-32 X 7/16 BUT HD CAP SS 4.00 WATER-BLOCK ASSEMBLY
O-RING 3/32 B1000-133 O-RING 3/32 X 1 13/1 1.00 WATER-BLOCK ASSEMBLY
APOGEE-H APOGEE WATERBLOCK HOUSING 1.00 WATER-BLOCK ASSEMBLY
APOGEE-BRKT APOGEE HOLD-DOWN PLATE 1.00 WATER-BLOCK ASSEMBLY
APOGEE-BP APOGEE BASE PLATE 1.00 WATER-BLOCK ASSEMBLY
B1000-2.5X50 BUNA-N 70D BLACK O-RING 2.00 FITTINGS
PM4S-6BN 1/4" - 1/8 NPSM TO 3/8" ID 2.00 FITTINGS
PM4S-8BN 1/4" - 1/8 NPSM TO 1/2 ID 2.00 FITTINGS
22HC04688 15/32" HOSE CLAMP 2.00 FITTINGS
22HC0672B 43/64" PREMIUM HOSE CLAMP 2.00 FITTINGS
SPRING6 SPRING FOR MCW6000-775 4.00 COMMON HARDWARE
6-32 HEX CAP 6-32 ACRON NUT 4.00 COMMON HARDWARE
12SWS0444 NYLON SHOULDER WASHER 8.00 COMMON HARDWARE
LOCKWASHER6 LOCK WASHER #6 6.00 COMMON HARDWARE
FW140X250X0215FB BLK BLACK FIBER WASHER .140X.250X. 10.00 COMMON HARDWARE
632.112PHPMS 6X32 X 1 1/2 PHILIPS PAN HEAD 4.00 COMMON HARDWARE
6-32 NUT 6-32 NUT 4.00 COMMON HARDWARE
6-32 X 1 5/8 6-32 X 1 5/8 4.00 XEON SCREWS
WASHER-0148X0266X0040-91007A619 LOCK WASHER #6 X 0.040 4.00 AMD SOCKET 754/939/940,AM2 HARDWARE
90272A153-6-32X1.00-PHILIPS SCREW 6-32 X 1” PHILIPS SCREW 4.00 AMD SOCKET 754/939/940, AM2 HARDWARE
13RS040637 ROUND SPACER 4.00 AMD SOCKET 754/939/940,AM2 HARDWARE
APOGEE-AM2-BP APOGEE AM2 BASE PLATE 1.00 AMD SOCKET AM2 HARDWARE
ARCTIC CÉRAMIQUE ARCTIC CÉRAMIQUE 1.00 THERMAL COMPOUND
Common installation guidelines
‰ Removal of the motherboard is necessary to install the mounting posts in all cases, except for AMD® socket 754, 939, 940
and AM2.
‰ Two sets of barb fittings are supplied to accommodate high-performance circuits: 3/8” barbs, and ½” barb.
‰ The Apogee water-block may be installed in any direction. Simply rotate the water-block in your hand prior to fasten it to the
processor when you are filling up the circuit. This will purge it from any air bubbles.
‰ The inlet and outlet are interchangeable with respect to flow direction.
‰ Coolant: use of distilled water is mandatory. Swiftech’s HydrX coolant is recommended as an antifungal, and corrosion
inhibitor.
1. Step-by step
‰ Install the fittings with their o-rings into the waterblock. Tighten each fitting until the flange of the fitting mates with the ledge
of the water-block o-ring groove, then lock it by adding ¼ to ½ turn.
‰ Remove the existing heatsink from your motherboard.
‰ Apply the provided Arctic Céramique thermal compound to the CPU following the comprehensive installation instructions
provided here: http://www.arcticsilver.com/ceramique_instructions.htm
‰ Install the Apogee water-block following the individual installation schematics for each type of CPU socket provided
hereafter.
‰ Connect the tubing to the water-block hose-barbs. Use the provided hose-clamps to secure the tubing to the barbs.
2. Individual installation schematics
The provided mounting hardware is common to Intel® Pentium® 4 socket 478, socket LGA775, and AMD® socket 462. AMD® socket 754, 939,
940, and AM2 mounting hardware is identified in a separate pack, as well as Intel® Xeon hardware. A separate hold-down plate is provided for
AMD AM2 socket. The mounting hardware for Intel Xeon “Nocona” class processors (800Mhx FSB motherboards) is sold separately under part #
AP-NC604.
IMPORTANT DISCLOSURES
While all efforts have been made to provide the most comprehensive tutorial possible, Swiftech assumes no liability expressed or implied for any damage(s) occurring to your components
as a result of using Swiftech cooling products, either due to mistake or omission on our part in the enclosed instructions, or due to failure or defect in the Swiftech cooling products.
WARRANTY Our products are guaranteed for 12 months from the date of delivery to the final user against defects in materials or workmanship. During this period, they will be repaired or
have parts replaced provided that: (I) the product is returned to the agent from which it was purchased; (II) the product has been purchased by the end user and not used for hire purposes;
(III) the product has not been misused, handled carelessly, or other than in accordance with any instructions provided with respect to its use. This guarantee does not confer rights other
than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an extra benefit and does not affect your statutory rights
as a consumer.