Indesit FIE76GPK-AIX - Manual (Page 20)

20
GB
The electronic cooking
programmer
This feature allows you to program the oven or the grill as follows:
• delayed cooking time for a specified period;
• immediate start for a specified period;
• timer.
Button Functions:
: Timer with hours and minutes;
: cooking time;
: end cooking time;
: Manual change;
: set cooking time (to count down);
: set cooking time (to start from zero)
How to reset the digital clock
After the appliance has been connected to the power supply, or
after a power cut, the clock display will automatically reset to 0:00
and begin to blink.
• Press the and buttons consecutively and then reset
the time (within 4 seconds) using the and buttons.
The button advances the hours.
The button decreases the hours.
The time can also be changed in the following two ways:
1. Repeat all of the steps above.
2. Press the button, and then use the and buttons to reset
the time.
Manual operation of the oven
Once the time has been set, the programmer automatically switches
to manual mode.
Note: Press the button to restore the manual mode after every
“Automatic” cooking session.
Adjusting the volume of the buzzer
After selecting and confirming the clock settings, use the
button to adjust the volume of the alarm buzzer.
Delayed cooking time for a specified period
The total cooking time as well as the time at which the cooking will
finish must be set. If we assume that the time display reads10:00:
1. Turn the oven control knob to the setting and temperature desired
(example: static oven mode at 200°C).
2. Press the button and then set the cooking time (within four
seconds) using the and buttons. Supposing the cooking
time is set to 30 minutes, the display will read as follows:
+
Release the button, and within 4 seconds, the current time will reappear
with the m symbol along with the word “auto”
3. Press the button and then use the and buttons to set
the time for when the cooking program should end. Let us
imagine this time to be 1:00 p.m. =
4. After the button has been released, the current time will be
displayed after approximately 4 seconds:
?
When “auto” is on, it indicates that the length of cooking time
and the time it is due to finish have been programmed in
automatic mode. At this point, the oven will turn on automatically
at 12:30 and turn off after 30 minutes. When the oven is turned
on, the symbol m will be displayed for the entire cooking time.
The cooking duration can be displayed at any time by pressing
the button , and the time it is due to finish may be displayed
by pressing the button .
Once cooking is completed, the timer will ring; to turn it off, simply
press any button except the and buttons.
Immediate start for a specified period
By programming just the duration (points 1 and 2 of the “Delayed
cooking time for specified period” section), cooking will begin
immediately.
To cancel a cooking schedule already
programmed
Press the button, and use the button to set the time to:
,
then press the manual cooking mode button .
Timer Feature
The timer feature allows you to enter a specific amount of time and
begins to count down. This feature does not turn the oven on or off;
it merely sounds when the time has elapsed.
When the button has been pressed, the display will read as
follows:
,
Then use the and buttons to set the desired time.
As soon as the button has been released, the timer will start to
count down and the current time will be displayed.
.
After the time has expired, an audible signal will be emitted, which
can be turned off by pressing any button (except the and
buttons). At this point the symbol will also turn off.
Correction/Cancellation of data
• The data entered can be changed at any time by pressing the
corresponding button and the or buttons.
• When the data for the cooking duration is cancelled, the data
for the time cooking is due to end is also cancelled automatically,
and vice versa.
• If the oven has already been programmed, it will not accept
times for the end of cooking which are before the start of the
programmed cooking process.