Indesit BAAN-40-FNF-D-(1) - Manual (Page 53)

GB
53
1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with water
through the opening provided.
2. Take care not to exceed the level indicated (MAX WATER
LEVEL). Excess water prevents the ice cubes from
dispensing (if this happens, wait for the ice to melt and
empty the tray).
3. Turn the tray 90°: due to the connected compartments each
mould fills with water (see diagram).
4. Close the opening with the lid provided and put the tray
back.
5. When the ice has formed (minimum time approximately 8
hours) knock the tray against a hard surface and wet the
outside so that the ice cubes come loose and take them out
through the opening.
WATER LEVEL
MAX
WA
TER LEVEL MAX
WA
TER LEVEL MAX
Start-up and use
Starting the appliance
! After transportation of the appliance, carefully place it in an
upright position and wait at least 3 hours before connecting it to
the electricity mains, to make sure it operates as it should.
• Clean the inside of the refrigerator well using warm water
and bicarbonate of soda before placing food inside it.
• The appliance comes with a motor protection control system
which makes the compressor start approximately 8 minutes
after being switched on. The compressor also starts each
time the power supply is cut off whether voluntarily or
involuntarily (blackout).
Freezer Compartment
When the product is switched on the freezer compartment is
set to its default value of -18°C. We recommend that the SUPER
FREEZE function is set (the freezer status bar continues to
display the set value) in order to accelerate the cooling process
of the compartment; when the inside of the compartment has
reached its optimal temperature the function will be deactivated
and the food may be placed inside.
Refrigerator Compartment
When the appliance is switched on the refrigerator
compartment is set to its default value of +5°C. We recommend
that the SUPER COOL function is set (the refrigerator status bar
continues to display the set value) in order to accelerate the
cooling process of the compartment. After a few hours it will be
cool enough for food to be placed inside.
Navigating the display
Setting the temperatures:
If the product is switched on, the refrigerator and freezer status
bars will indicate the temperatures set at that moment. To
change them, simply press the - and + buttons corresponding
to the compartment for which you wish to change the set
temperature. More specifically, each time one of the buttons
is pressed the temperature is increased or decreased by 1°,
and the level of cold is adjusted accordingly.The temperature
values that may be selected for the refrigerator compartment
are +12°C, +7°C, +6°C, +5°C, +4°C, +3°C and +2°C, while the
values that may be set for the freezer are -18°C, -19°C, -120°C,
-21°C, -22°C, -24°C and -26°C.
The temperatures are automatically set to +5C for the
refrigerator compartment and -18C for the freezer
compartment (these are standard food storage values.
When the “ECO” function is active, the appliance automatically
adjusts the temperatures according to the conditions inside
and outside the refrigerator; the operation of this function is
signalled by the text “AUTO”.
Whenever it is necessary to activate the “ECO” function at
temperatures that are different to the standard storage values,
the “ECO” button must be pressed as soon as the function
is activated and held down while the new temperatures are
set using the - and + buttons. Under these conditions,
the temperatures may be set to 4°C, 5°C and 6°C for the
refrigerator compartment and -18°C, -19°C and -20°C for the
freezer compartment.
When the HOLIDAY function is active the temperature may not
be adjusted, however the appliance adjusts itself automatically
so that the optimal settings for the situation are used: +12C
for the refrigerator compartment and -18C for the freezer
compartment. This function is indicated by the text “AUTO”.
To activate and deactivate the functions simply press the
relevant button and the function status will be signalled by the
corresponding LED switching on or off.
Several functions (SUPER COOL, SUPER FREEZE, BOTTLE
CHILL, ECO) are incompatible with others (HOLIDAY,...);
remember that there is a pre-set order of priority which will help
you to use the product in the best possible way.
When the BOTTLE CHILL function has finished, press the
BOTTLE CHILL button to stop the corresponding LED from
flashing and to silence the sound signal. This flashing and
sound signal indicates that the function is complete and that
the bottle should be removed from the freezer compartment.
Child Lock
In order to activate the Child Lock function, the Child Lock
button must be pressed for 2 seconds; the activation of the
button lock is confirmed by a short beep and the illumination of
the corresponding LED.
To deactivate the function, press the Child Lock button for 2
seconds; deactivation will be confirmed by a short beep and by
the corresponding LED switching off.
! The FREEZER status bar is also used to indicate an unusual
temperature increase in the freezer compartment (see
Troubleshooting).