A.J. Antunes & Co MS-250 9100439 - Manual (Page 7)

7 P/N 1010984 Rev. D 03/12
operaTinG inSTrucTionS
1. Turn the power on and allow the unit
to preheat for approximately 20-30
minutes.
NotE: Do Not push any button during
warmup time. the flashing green ready
Light indicates that the unit is Not
warmed up. the green ready Light will
become steady when the unit is warmed
up.
2. Pull out the Spatula and set the prod-
uct to be steamed onto the Spatula.
3. Push the Spatula fully into the
steamer.
4. Steam the product by pressing either
the Single Shot button for a single
burst or the Operate button for a
timed cycle.
NotE: Mfg. Nos. 9100427 and 9100434 do
Not have the Single Shot function.
5. Remove the steamed product.
proGraMMinG
CYC (total Cycle time) refers to the total
programmed steam time set for the product.
SHo (Shot Interval time) refers to the time set
between shots of steam during a complete cycle.
H2o setting (Steam Shot time) refers to the
water volume consumed during each water
pump activation.
The amount of steam produced by your
Miracle Steamer depends on the amount of
water sprayed onto the steam generator.
Flooding of the generator may occur if the
H2O setting is too high. To prevent flooding,
the Shot Interval Time (SHO) can be increased
to allow more time for generator heat recov-
ery. Adjustments should be made to both
values to determine the best settings for your
cooking needs.
1. Turn the unit on. The unit displays the
factory programmed Total Cycle Time
in minutes and seconds.
2. Press and release to change the
control from OPERATION to PROGRAM
mode.
3. To change the Total Cycle Time in min-
utes, press ▲ or ▼ to change the time.
WarNING
To avoid injury, be careful when pulling the
spatula out from the unit. Be sure to allow
steam to escape before putting hands or
face over the steamer.
4. Press and release again, and press
▲ or ▼ to change the Total Cycle
Time in seconds.
5. To change the SHO factory settings,
make sure the control is in PROGRAM
mode, then press and hold both
▲
and ▼ simultaneously for 1-2 seconds
and release. “SHO” will be displayed.
6. Press and release and then press
▲ or ▼ to change the SHO in seconds.
7. Press and release again and press
▲ or ▼ to change the SHO in minutes.
8. Press and release again and
“H2O” will be displayed.
9. To change the H2O (Steam Shot time),
press and release the Program button
again to display the setting. Use
▲ or
▼ to increase or decrease the time.
10. Press the Single Shot or Operate but-
tons to store the changes, exit the
PROGRAM Mode, and initiate the
cooking cycle.
IMportaNt: 208V and 220/240V Miracle
Steamers are factory programmed for the
following recommended settings:
• Total Cycle Time (CYC) = 15 min., 00
secs. (Range: 3 seconds to 99 minutes
59 seconds)
• Shot Interval Time (SHO) = 00 min., 20
secs. (Range: 3 seconds to 5 minutes
59 seconds)
• Steam Shot Time (H2O) =
MS-150: 1_00
MS-250: 0_70
(Range: 0_10 second to 2_50)
IMportaNt: 120V Miracle Steamer is fac-
tory programmed for the following recom-
mended settings:
• Total Cycle Time (CYC) = 2 min., 00
secs. (Range: 3 seconds to 99 minutes
59 seconds)
• Shot Interval Time (SHO) = 00 min., 20
secs. (Range: 3 seconds to 5 minutes
59 seconds)
• Steam Shot Time (H2O) = 0_40
(Range: 0_10 seconds to 2_50)
NotE: the Single Shot or operate buttons
may be pressed at any time during pro-
gramming to store the changes and exit
the proGraM Mode.
NotE: If a change is not made within 5
seconds at any time during the program-
ming process, all changes made up to that
point are stored in memory and the con-
trol reverts to the opEratIoN Mode.
UP DOWN
SINGLE SHOT
PROGRAM
POWER
READY
START/STOP
ready Light
power
Switch
operate
Button
Message
Display
Single Shot
Button
Figure 5a. operating Controls
(all Units Except Mfg. Nos.
9100427 & 9100434)
ready Light
power
Switch
operate
Button
Message
Display
Figure 5b. operating Controls
(Mfg. Nos. 9100427 & 9100434)