A.J. Antunes & Co DFWF-250 9100156 - Manual (Page 6)

6 P/N 1010678 Rev. K 08/12
POWER
GENERAL INFORMATION
ALL MODELS
When the OPERATE button is pressed, power
is supplied to the water pump (Water Tank
models) or solenoid valve (Direct Water
Hookup models). The pump/solenoid oper-
ates and water sprays onto the heated steam
generator. The water flashes immediately into
steam and steams the product.
TIMER MODELS DFW/DFWT/DFWF–
150/250 EXCEPT DFWF-250 WITH
MFG. NO. 9100147
On Timer Models, one of two operational modes
can be used: Single Shot or Timed Cycle.
Single Shot
The OPERATE button is pressed and released
to initiate a single steam shot. The Control
Board applies power to the water pump/sole-
noid and a shot of steam occurs.
Timed Cycle
The control is used to set the desired steam
time (up to 99 minutes, 59 seconds). When
the START/STOP button (Figure 3) is pressed,
the Control Board applies power to the water
pump/solenoid at regular intervals for the
duration of the displayed cycle time. The dis-
play counts down to zero, sounds an audible
signal when the cycle is complete, and then
reverts back to the original programmed cycle
time. The unit is ready for the next cycle when
the green ready light is on.
IMPORTANT: Timer Models are factory pro-
grammed for the following recommended
settings:
• Total Cycle Time = [15.00] (15 min-
utes)
(Range: 3 sec. to 99 mins 59 secs)
• Shot Interval Time (SHO) = [00:20] (20
seconds)
(Range: 3 secs to 5 mins 59 secs). 20
seconds is recommended.
• Water Volume (H2O) =
DFW/DFWT/DFWF-250 - [0_50]
DFW/DFWT-150 - [0_80]
(Range: 0.10 seconds to 2.50)
The above settings convert approximately 3/4
oz. (25 milliliters) of water into to steam every
20 seconds for 15 minutes. To change any of
these settings see the appropriate Operating
Instructions for your specific unit.
OPERATING INSTRUCTIONS
NON-TIMER MODELS
1. Turn the power on (Figure 2).
2. Allow the unit to preheat for approxi-
mately 30 minutes.
NOTE: Do NOT push the OPERATE button
during warm-up.
3. Open the top cover and place the
product to be steamed onto the trivet,
then close the cover.
4. Press the OPERATE button for 1 sec-
ond then release and wait 20 seconds
for the steam to penetrate the prod-
uct. Repeat if product requires more
steam.
NOTE: Pressing and holding the OPERATE
button for longer than 1 second at a time,
and/or too often (before 20 seconds), will
flood out the Generator surface (Figure 6)
and result in poor steaming.
5. Remove steamed product.
TIMER MODELS
1. Turn the power on (Figure 3).
2. Allow the unit to preheat for approxi-
mately 30 minutes.
IMPORTANT: The flashing green Ready
Light will become steady when the unit is
up to temperature and ready to be used.
IMPORTANT: Do NOT push the OPERATE
button during warm-up. The flashing
green Ready Light indicates unit is not up
to temperature.
3. Open the top cover and place the
product to be steamed onto the trivet,
then close the cover.
4. Single Shot: Press the OPERATE but-
ton for 1 second then release and wait
20 seconds for the steam to penetrate
the product.
Timed Cycle: Press the START/STOP
button to begin the steaming cycle.
Display will count down to zero.
5. Remove steamed product.
WARNING
To avoid injury, be careful when opening top
cover. Be sure to allow steam to escape
before putting hands or face over the
steamer.
READY
UP DOWN PROGRAM START/STOP
POWER
Power
Switch
Operate
Button
Figure 3. Control Panel
(Timer Models)
Figure 2. Control Panel
(Non-Timer Models)
Ready Light
Power Switch
Operate
Button
Message
Display
Start/Stop
Button