American Standard 6802 Series - Manual (Page 2)

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
A m e r i c a n S t a n d a r d I n c . 1 9 9 9 C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 223-0068
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
Turn off hot and cold water
supplies before beginning.
CAUTION
VALVE INSTALLATION
DRAIN INSTALLATION
SERVICE
1
6
2
4
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
LOCKNUT
SPOUT
EXTENSION
CLIP
CLIP
LIFT ROD
EXTENSION
THUMBSCREW
ACTUATOR
ROD
CARTRIDGE
SCREEN
SPRING
CLIP
STOP
WASHER
RETAINER
RUBBER
WASHER
RUBBER
GASKET
SINK
Insert BASE or SPOUT shank through
center hole of SINK, making sure
RUBBER GASKET is properly positioned.
SPOUT OR BASE ASSEMBLY
Assemble RUBBER WASHER,
RETAINER, and LOCKNUT onto
threads of SPOUT from underside
of SINK.
Insert LIFT ROD through SPOUT (or
BASE) and slot of RETAINER.
Align SPOUT and tighten LOCKNUT.
Be sure slot in BRASS WASHER is
positioned to the rear as shown.
Prepare TUBE and TEE ASSEMBLY to fit
available VALVE location. If necessary, cut
and/or bend TUBING carefully. Make sure
tube bend is close to the TEE so that it
will not effect the compression joint at
the VALVE.
Place RUBBER RING into ESCUTCHEON
and screw ESCUTCHEON onto VALVE
BODY until snug against internal stop.
Tighten LOCKNUT to secure VALVE
position. Attach COUPLING to TEE
and tighten.
ACTUATOR
ROD
TAIL
PIECE
TEST INSTALLED FAUCET
5
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
Apply a bead of PUTTY around the underside
of DRAIN PLUG flange and insert DRAIN PLUG
into SINK drain hole.
Hold DRAIN PLUG firmly to prevent
turning, and assemble the GASKET,
WASHER, and LOCKNUT from underneath
the SINK.
Insert GASKET into COUPLING and
attach COUPLING to DRAIN PLUG.
Align COUPLING so that the
ACTUATOR ROD faces rear of
SINK and tighten LOCKNUT to
secure position.
Unscrew ACTUATOR NUT and withdraw the ACTUATOR ROD.
Drop STOPPER into DRAIN PLUG with the OFFSET SQUARE SLOT
in line with ACTUATOR ROD opening.
Reassemble ACTUATOR ROD. Make sure ROD is inside offset
square slot of the stopper. Tighten ACTUATOR NUT.
Insert threaded end of TAILPIECE into lower end of COUPLING.
Connect other end of TAIL PIECE to the TRAP.
Slide EXTENSION onto ACTUATOR ROD and secure with CLIP.
Slide EXTENSION onto LIFT ROD and tighten THUMBSCREW.
Adjust LIFT ROD stroke for proper opening and closing of the
stopper.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90
° and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90
° .
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
TEE
SCREW
O-RING
O-RING
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
SHANK
Remove COUPLING NUT, FRICTION RING,
and RUBBER FERRULE from each valve and
slide onto tubing.
Push TUBING ends into VALVE side outlets. Insert
VALVES into mounting holes from underside of SINK.
Press TEE onto SHANK of SPOUT making certain that the
SHANK O-RING is properly seated on SHANK.
Slide RUBBER FERRULE, FRICTION RING,
and COUPLING NUT to outlet of VALVE
and tighten COUPLING NUT firmly.
Repeat on other VALVE.
Connect HOT water supply to inlet of left
VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Models 6802 and 6832 only)
(Models 6801 and 6831 only)
PUTTY
FLANGE
DRAIN
PLUG
RUBBER
GASKET
WASHER
LOCKNUT
SINK
3
VALVE INSTALLATION (continued)
M 3 4 3 7 5 C