Alpine CDE-9872RE - Manual (Page 22)

20
-EN
5
Turn the Rotary encoder (CDE-9874 Series only) or
press
and (CDE-9872 Series only) to select the
desired Song, and then press / /ENT.
• After pressing and holding / /ENT for at least 2 seconds while
in each hierarchy (except SONG hierarchy), all songs of the selected
hierarchy are played back.
• After selecting [ALL] in the search mode with“*”, press and hold
/ /ENT for at least 2 seconds to play back all songs in the iPod
or selected search mode.
• While in the search mode, if you press and hold /ESC for 2
seconds, or no operation is performed for 10 seconds, the search
mode is cancelled.
• In the search mode, pressing /SOUND (CDE-9874 Series only)
or /AUDIO (CDE-9872 Series only) will return to the previous
mode.
• Search cannot be made during M.I.X. play.
• “NO SONG” will be displayed if there are no songs in the selected
playlist in the PLAYLIST search mode.
• “NO PODCAST” will be displayed if there is no podcast data in the
iPod in the PODCAST search mode.
• If “iPod name” stored in the iPod is selected in the desired Playlist
search mode, and / /ENT is pressed, you can search for all
songs in the iPod. Also, if you press and hold / /ENT for at least
2 seconds, all songs in the iPod are played back.
• Depending on the iPod, podcast search is not supported.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 20.
Quick Search (CDE-9874 Series only)
You can search a song from all songs in the iPod without selecting an
album, artist, etc.
1
Press and hold /ESC for at least 2 seconds to
activate the Quick Search mode.
2
Turn the Rotary encoder to select a desired song.
The selected song is played back immediately.
• Press and hold /ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
• If many songs are in the iPod, it takes time to search for songs.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 20.
• This function is inactive during repeat (RPT) playback.
Direct Search Function
The unit’s direct search function can be used to search for an album,
song, etc., more efficiently. In Playlist/Artist/Album/Song/Podcast/
Genre/Composer mode, you can quickly target any song.
In the search mode, press any one of the preset
buttons (1 through 6) to quickly skip over a
designated percent of your song content.
Song search example:
If there are 100 songs in your iPod, they are divided into 6
groups using percentages (shown below). These groups are
assigned to the preset buttons (1 through 6).
Example 1:
Suppose the song you are searching for is located at around
the middle (50%) of your library: press button 4 to jump to the
50th song and turn the Rotary encoder (CDE-9874 Series
only) or press
and (CDE-9872 Series only) to find the
desired song.
Example 2:
Suppose the song you are searching for is located near the
end (83%) of your library: press button 6 to jump to the 83rd
song and turn the Rotary encoder (CDE-9874 Series only) or
press
and (CDE-9872 Series only) to find the desired
song.
Select Playlist/Artist/Album/Genre/
Composer
Playlist/Artist/Album/Genre/Composer can be easily changed.
For example, if you listen to a song from a selected album, the album
can be changed.
Press 1 /AF or 2 to select the desired Playlist/Artist/
Album/Genre/Composer.
• If the song search mode was used to select a song, this function is
inactive.
• If an album is selected during an artist search, other albums by that
artist are searchable.
• This function is inactive during shuffle (M.I.X.) playback.
All 100 songs (100%)
0% 17% 33% 50% 67% 83%
Preset
buttons
1 2 3 4 5 6
Songs
First
song
17th
song
33rd
song
50th
song
67th
song
83rd
song