Panasonic ER2301 - Manual (Page 3)

4
This Beard/Hair Trimmer is for the
trimming and care of mustaches,
beards and hair.Trimming length
can be adjusted between 2 to
1 8 m m . T h e T r i m m e r c a n b e
operated either from an AC power
source or on its own rechargeable
battery.
Parts identification
(See Fig. 1)
A Switch
Slide up to turn on, slide down
to turn off.
B Charging Indicator Lamp
Lights when the unit is con-
nected with the adapter L to an
AC power source for charging.
C Main Blade
A precision 39mm-wide blade
which can be used with the
comb attachment G .
D Thinning Plate
When thinning,slide the thinning
plate up until it firmly clicks in
position. (See Fig. 2)
E Thinning Plate Lock Button
Press and hold while sliding the
Thinning plate D down to set
the Thinning Plate back to its
original position.
F Dial
Turn the dial to a higher set-
ting to raise or lower the comb
attachment G to the desired
length (between 2 and 18mm).
G Comb Attachment
Use this to control the trimming
length. (See Fig. 4) Be sure to
slide the Thinning plate down to
“1” before attaching the attach-
ment. (See Fig. 3)
H Stationary Blade
I Moving Blade
J Cleaning Lever
Push this lever to remove bits of
hair caught between the station-
ary blade and the moving blade.
K Blade Block
Release to remove the blade
block from the housing to clean
or replace the blade. (See Fig.
9)
L Adapter
Use this to connect the Trimmer
to an AC power source for re-
charging or for AC operation.
M Oil
Lubricate the space between
the stationary and moving blade
with 2 or 3 drops of oil after use.
(See Fig. 11)
N Cleaning Brush
Trimming length indicator
Indicator Trimming Length
1 2.0mm
●
3.0mm
2 4.5mm
●
6.0mm
3 7.5mm
●
9.0mm
4 10.5mm
●
12.0mm
5 13.5mm
●
15.0mm
6 16.5mm
●
18.0mm
P00-07_EN_ER2301.indd 4 P00-07_EN_ER2301.indd 4 2008/04/04 10:31:25 2008/04/04 10:31:25
5
Operation
Rechargeable-battery operation
Charge the battery by plugging the
Trimmer into an AC source using
the adapter. The switch should be
set to 0·CHARGE during charging.
An 8-hour charge will provide ap-
prox. 30 minutes of use.
AC operation
Plug the Trimmer into an AC power
source using the adapter with the
switch set to 0·CHARGE.Wait
about 10 seconds, then switch the
trimmer on. After use, return the
switch to the 0·CHARGE position.
Trimming of Beard
Place the angled face of the comb
against the skin and cut the beard
by moving the trimmer in all direc-
tions to obtain a uniform cut. (See
Fig. 5)
With curly facial hair, the comb
attachment may not cut all of the
hair. In this case, remove the comb
attachment and use a conventional
comb to draw out the remaining
uncut hair.
(See Fig. 6)
When shaping the beard, remove
the comb attachment. Place the
angled edge against the skin and
make the border of the beard even.
How to use the thinning function
(See Fig. 7)
First, slide the Thinning plate up
to “1/3” until it clicks. (See Fig. 2)
While applying the blade point at
right angles to the hair, run the
trimmer slowly across the head as
if combing the hair. After thinning,
slide the thinning plate back while
pushing the Thinning Plate Lock
Button. (See Fig.3)
Notes on thinning
For thinning, confirm that the thin-
ning plate is set to the 1/3 (right)
position.Incorrect setting may result
in excessive cutting.
If a difference in level is produced,
lightly thin to compensate.
If thick and thin portions are pro-
duced, or if there are portions with
an excessive amount of hair, thin
the appropriate portions to com-
pensate.
Point:
Thin the hair gradually while check-
ing the overall balance.
Maintenance
Blades
1. Brush out the cutting mecha-
nism. (See Fig. 8)
2. Hold body of the trimmer with
Panasonic mark upwatds, place
the thumb against the blades,
and push them away from the
main body. (See Fig. 9)
3. Push down the cleaning lever
to raise the moving blade and
brush in between the blades.
(See Fig. 10)
4. Put a few drops of oil on the
blades. (See Fig. 11)
Blade Life
Blade life will vary according to
the frequency and length of use.
For example, using the unit for 10
minutes every 3 days, the life ex-
pectancy is approximately 3 years.
If cutting efficiency is reduced sub-
stantially despite proper mainte-
nance, the blades have exceeded
their service life and should be
changed. The replacement part
no. is ER965.
P00-07_EN_ER2301.indd 5 P00-07_EN_ER2301.indd 5 2008/04/04 10:31:26 2008/04/04 10:31:26
Refine_08-04-04 10:36:40
Refine_P00-07_EN_ER2301_005.p1.pdf Refine_P00-07_EN_ER2301_004.p1.pdf
Refine_08-04-04
10:36:40
B461518_ER2301_Tori_EU 3 08-04-23 11:30:19