Panasonic EY6220N - Manual (Page 5)

– 8 –
E Main switch lock
After use, set the main switch lock at
the lock position to prevent acciden-
tal operation.
F Battery pack (EY9021)
CAUTION
When you charge the battery pack
for the first time, or after prolonged
storage, charge it for about 24 hours
to bring the battery up to full capacity.
1. Press the battery pack release
buttons G on both sides and pull
the pack away from the tool.
2. Charge the battery pack using the
battery charger.
3. After the charging has been com-
pleted, remove the battery pack
from the charger and connect it to
the tool. Disconnect the charger
from the power source when not in
use.
Battery Pack Life
The rechargeable batteries have a
limited life. If the operation time
becomes extremely short after
recharging, replace the battery with a
new one.
Note: Use under extremely hot or
cold conditions will reduce
operation capacity per charge.
Main switch
lock
G Battery pack release button
H Battery charger (EY0225)
1. Plug the charger into an AC outlet.
NOTE: Sparks may be produced
when the plug is inserted
into the AC power
supply, but this is not a
problem in terms of safety.
2. Insert the battery pack firmly into
the charger.
#
$
Battery
pack
Battery
charger
To AC
outlet
Lock
Lock
3. During charging, the charging
lamp will be lit.
When charging is completed, an
internal electronic switch will auto-
matically be triggered to prevent
overcharging.
B Charging will not start if the bat-
tery pack is warm (for example,
immediately after heavy-duty
operation). The orange standby
lamp will be lit until the battery
cools down. Charging will then
begin automatically.
4. When charging is completed, the
charging lamp will start flashing rapidly.
5. If a fully charged battery pack is
inserted into the charger again, the
charging lamp may light up and then
flash slowly. After several minutes,
the charging lamp may flash quickly
to indicate the charging is completed.
6. If the charging lamp does not light
immediately after the charger is
plugged in, or if after the standard
charging time the lamp does not go
off, consult an authorized dealer.
NOTE: • When a cold battery (of
about 5°C or less) is to be
charged in a warm room,
leave the battery in the room
for at least one hour and
charge it when it has warmed
up to room temperature.
(Failing to do so may result in
EY6220取説(USA) 07.4.20 13:20 ページ8
– 9 –
Maintenance
Use only a dry, soft cloth for wiping the
unit. Do not use a damp cloth, thinner,
benzine, or other volatile solvents for
cleaning.
BATTERY RECYCLING
ATTENTION:
A nickel cadmium battery that is
recyclable powers the product you have
purchased. At the end of its useful life,
under various state and local laws, it is
illegal to dispose of this battery into your
municipal waste stream.
Please call 1-800-8-BATTERY for
information on how to recycle this battery.
I #1 Philips bit
J Slotted head bit
K #2 Philips bit
LAMP INDICATIONS
less than a full charge.)
NOTE: • Cool down the charger when
charging more than two
battery packs consecutively.
CAUTION: • Do not use power source
from an engine generator.
Flashing
Charging lamp
Red
Standby lamp
Orange
Now charging
Charging is completed
Battery pack is warm. Charging will begin
when temperature of battery pack drops.
Charging is not possible. Clogged with
dust or malfunction of the battery pack.
Charger is plugged into the AC outlet.
Ready to charge.
Flashing
Lit
Flashing quickly
Lit
EY6220取説(USA) 07.4.20 13:20 ページ9
Refine_07-04-20 13:26:31
Refine_EY6220(USA).9.p1.pdf Refine_EY6220(USA).8.p1.pdf
Refine_07-04-20
13:26:29
B437428_EY6220_Tori_USA 5 07-04-23 13:36:05