Panasonic PT-D7500E - Manual (Page 2)

2
PT-D7500
DLP™-Based Projector
S P E C F I L E
Specifications
Main Unit
Power supply: 220 – 240 V AC, 50/60 Hz
Power consumption: 800 W (800 VA) (12 W during standby mode with fan stopped)
DMD™ device: Panel size: 0.7˝ diagonal (4:3 aspect ratio)
Display method: DMD™ (x 3, R/G/B), DLP™ system
Pixels: 786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Lens: Optional powered zoom/focus lenses
Lamp: 300 W UHM™ lamps (x 2) (BriteOptic™ Dual Lamp System)
Screen size: 70 – 600 inches (1,778 –15,240 mm) diagonally (4:3 aspect ratio)
* 70 – 300 inches (1,778 –7,620 mm) diagonally (4:3 aspect
ratio) with the ET-D75LE5
Brightness : 5,000 lumens (dual lamp, high power mode)
Centre-to-corner uniformity ratio: 90%
Contrast: 1,000:1 (full on/full off, high contrast mode, with a high-contrast lens)
(brightness: 3,500 lumens)
600:1 (full on/full off, normal contrast mode with a standard lens
Resolution: RGB: 1,024 x 768 pixels
(1,600 x 1,200 pixels compatible, compression mode)
Video: 560 TV lines
Scanning frequency: RGB: Horizontal: 15 –100 kHz, Vertical: 24 –120 Hz,
Dot clock: 20 –162 MHz
* Images may not be normally displayed when projecting moving pic-
tures with vertical frequency which is not between 45 Hz and 61 Hz.
YP B P R (YC B C R ): 480i: f H 15.75 kHz; f V 60 Hz, 576i: f H 15.63 kHz; f V 50 Hz,
480p: f H 31.5 kHz; f V 60 Hz, 576p: f H 31.25 kHz; f V 50 Hz,
720/60p: f H 45 kHz; f V 60 Hz, 1035/60i: f H 33.75 kHz; f V 60 Hz,
1080/60i: f H 33.75 kHz; f V 60 Hz, 1080/50i: f H 28.13 kHz; f V 50 Hz,
1080/25p: f H 28.13 kHz; f V 25 Hz, 1080/24p: f H 27 kHz; f V 24 Hz,
1080/24sF: f H 27 kHz; f V 48 Hz, 1080/30p: f H 33.75 kHz; f V 30 Hz
S-Video/Video: Horizontal: 15.75/15.63 kHz, Vertical: 50/60 Hz,
(PAL, PAL60, PAL-M, PAL-N, SECAM, NTSC, NTSC4.43)
Optical axis shift: Horizontal and vertical (powered)
Keystone correction range: Vertical: ±40° (±27° with the ET-D75LE5)
Installation: Ceiling/desk, front/rear
Terminals: RGB1 IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 1.4 Vp-p – 5.0Vp-p, 75Ω (positive/negative)
Y, P B , P R : Y: 1.0 p-p, 75Ω, P B,/ P R : 0.7 Vp-p, 75Ω
RGB2 IN/RGB1 OUT: D-sub HD 15-pin x 1, IN/OUT selection is operated with on-screen menu.
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD/VD/SYNC: 75Ω, TTL (positive/negative polarity)
Y, P
B
, P
R
: Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω
VIDEO IN: BNC x 1, 1.0 Vp-p, 75Ω
VIDEO OUT: BNC x 1, 1.0 Vp-p, 75Ω, active through
S-VIDEO IN: Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
SERIAL IN: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
SERIAL OUT: D-sub 9-pin x 1 (RS-232C/422 compliant) for external controller
REMOTE 1 IN: M3 jack x 1 for wired remote control or link control
REMOTE 1 OUT: M3 jack x 1 for wired remote control or link control
REMOTE 2 IN: D-sub 9-pin x 1 for external control (parallel)
Optional board slot: x 1
ET-MD95RGB
RGB/YP
B
P
R
IN: BNC x 5
R, G, B: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75Ω,
HD (H) / SYNC (H•V) • VD (V): 75Ω, TTL (positive/negative)
Y, P
B
, P
R
: Y: 1.0 p-p, 75Ω, P
B,/
P
R
: 0.7 Vp-p, 75Ω, BETACAM compatible
ET-MD95VM2
VIDEO BNC x 2 (IN, OUT)
VIDEO IN: 1.0 Vp-p, 75Ω or high impedance (auto selection)
VIDEO OUT: 1.0 Vp-p, 75Ω or high impedance (auto selection)
S-VIDEO IN: BNC x 2 (Y, C)
Y, C: Y: 1.0 Vp-p, C: 0.286 Vp-p, 75Ω
YC B C R IN: (BNC x 3, common with VIDEO and S-VIDEO connectors)
Y, C B , C R : Y: 1.0 p-p, 75Ω, P B,/ P R : 0.7 Vp-p, 75Ω
As of April 2004