Alpine cda-9886 - Manual (Page 15)

13
-EN
01GB05CDA9886.fm
ALPINE CDA-9886 68-09359Z43-A (EN)
Setting the Subwoofer Level
You can change the Subwoofer Level to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the SUBW. Level
Adjustment mode, and then press /ENT.
SUBW. Level* 1 Bass* 2 Treble* 2 HPF* 2 Black Out
SUBW. Level
3
Turn the Rotary encoder to select the desired
subwoofer level (0~+15).
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
* 1 When the subwoofer mode is set to OFF, its level cannot be adjusted.
Refer to “Turning Subwoofer ON/OFF” (page 15).
The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat” (page 12).
* 2 The function is inoperable when DEFEAT is set to ON.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the Bass
Adjustment mode, and then press
/ENT.
SUBW. Level* 3 Bass* 4 Treble* 4 HPF* 4
Black Out SUBW. Level
3
-1 Press BAND to select the desired bass center
frequency.
80 Hz 100 Hz 200 Hz 60 Hz 80 Hz
Emphasizes the displayed bass frequency ranges.
3
-2 Press SOURCE/ to select the desired bass
bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
3
-3 *5 Turn the Rotary encoder to select the desired
bass level (–7~+7).
You can emphasize or weaken the bass level.
4
Press and hold /ESC for at least 2 seconds to
return to normal mode.
• If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
• The bass level settings will be individually memorized for each
source (FM, AM, CD, etc.) until the setting is changed. The bass
frequency and bass bandwidth settings adjusted for one source are
effective for all other sources (FM, AM, CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
* 3 When the subwoofer mode is set to OFF, its level cannot be adjusted.
Refer to “Turning Subwoofer ON/OFF” (page 15).
* 4 The function is inoperable when DEFEAT is set to ON.
* 5 The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer to “Adjusting Subwoofer Level/Bass Level/ Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat” (page 12).
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
1
Press SOUND SETUP to activate the Sound Setting
mode.
2
Turn the Rotary encoder to select the Treble
Adjustment mode, and then press
/ENT.
SUBW. Level* 6 Bass* 7 Treble* 7 HPF* 7 Black Out
SUBW. Level
3
-1 Press BAND to select the desired treble center
frequency.
10 kHz 12.5 kHz 15 kHz 17.5 kHz 10 kHz
Emphasizes the displayed treble frequency ranges.
Setting the Bass Center Frequency
Setting the Bass Bandwidth
Q1 Q2 Q3 Q4
Setting the Bass Level
Setting the Treble Center Frequency
01GB00CDA9886.book Page 13 Friday, September 28, 2007 10:20 AM