Audio-Technica U891RWX - Manual (Page 2)

U 891Rx & U891RWx
Specifications
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
©2010 Audio-Technica U.S., Inc. audio-technica.com 0001-0267-00
11V to 52V DC phantom power source. It shall be capable of handling
sound input levels up to 130 dB with a dynamic range of 104 dB. Nominal
open circuit output voltage shall be 19.9 mV at 1 V, 1 Pascal. Output
shall be low impedance balanced (200 ohms). It shall offer outstanding
rejection of radio frequency interference (RFI).
The microphone shall be equipped with an activation switch that can be
set to any of three operating modes: “press-on/press-off,” “press-to-talk”
and “press-to-mute”.
The microphone shall incorporate self-contained electronics, eliminating
the need for an external power module. A 7.6 m (25') miniature output
cable with TA3F-type to XLRM-type connectors shall be supplied.
The output of the microphone shall be a TB3M-type connector. The
microphone shall include a switch to permit choice of flat response or 80
Hz low-frequency roll-off.
The microphone shall be equipped with an integral rotating output
connector that allows the cable to exit from either the rear or the bottom
of the microphone without the need to disassemble the microphone or
use tools to change the cable exit location.
The microphone shall have a maximum width of 84.0 mm (3.31"), a
maximum length of 108.0 mm (4.25") and a maximum height of 23.0
mm (0.91"). Weight shall be 264 grams (9.3 oz). The microphone shall
be housed in a die-cast case with a perforated steel grille. Finish shall
be low-reflectance black [white]. The microphone shall include a soft
protective pouch.
The Audio-Technica U891Rx [U891RWx] is specified.
In the interest of standards development, A.T.U.S. offers full
details on its test methods to other industry
professionals on request.
1 Pascal = 10 dynes/cm 2 = 10 microbars = 94 dB SPL
1 Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz SCALE IS 5 DECIBELS PER DIVISION
240˚
180˚
210˚
270˚
300˚
330˚
0˚
150˚
120˚
90˚
30˚
60˚
12" or more on axis LEGEND
Frequency in Hertz
Response in dB
10 dB
100 50 200 10k 5k 1k 500 2k 20k
Roll-off
frequency response: 30–20,000 Hz
polar pattern
Fixed-charge back plate, permanently
polarized condenser
Half-cardioid (cardioid in hemisphere
above mounting surface)
30-20,000 Hz
80 Hz, 18 dB/octave
–34 dB (19.9 mV) re 1V at 1 Pa
200 ohms
130 dB SPL, 1 kHz at 1% T.H.D.
104 dB, 1 kHz at Max SPL
68 dB, 1 kHz at 1 Pa
11-52V DC, 4 mA typical
Activation: on/off;
Switch function: press on/off,
momentary on, momentary off;
Flat, roll-off
264 g (9.3 oz)
108.0 mm (4.25") maximum length,
84.0 mm (3.31") maximum width,
23.0 mm (0.91") maximum height
TB3M-type
7.6 m (25.0') long, 3.2 mm (0.13")
diameter, 2-conductor, shielded cable with
TA3F-type and XLRM-type connectors
UE-O omnidirectional (360°)
UE-H hypercardioid (100°)
Soft protective pouch
Element
Polar pattern
Frequency response
Low frequency roll-off
Open circuit sensitivity
Impedance
Maximum input sound level
Dynamic range (typical)
Signal-to-noise ratio 1
Phantom power requirements
Switches
Weight
Dimensions
Output connector
Cable
Optional interchangeable elements
Accessory furnished