Custom Brackets Pan-Tilt Head AS - Manual

Using the Pan lock knob for drag may cause damage to unit. To properly
use Pan lock knob, either have it fully tighened, or fully loosened.
Lens lock knob
(press in and rotate
clockwise to tighten)
Tilt lock knob
(rotate counter-clockwise
to tighten)
Tilt drag knob
(rotate clockwise
to tighten)
P a n - T i l t H e a d A S I N S T R U C T I O N S
phone 440-446-0819
Toll Free 800-530-2289
website: www.custombrackets.com
email: [email protected]
32 Alpha Park
Cleveland, Ohio 44143
Made in USA
Quick release
reference lines
Lens plate
reference lines
Lens lock knob
Attach lens with lens plate
by loosening lens lock knob
completely, then place lens
plate into quick release. Tighten
lens lock knob completely, then
loosen 1/2 turn. Slide lens
forward or backward to balance,
then retighten lens lock knob.
If you have a replacement lens
foot, use the same procedure
above.
Install screw(s) into lens plate at the labeled
ends. The screw(s) and / or plate may be
damaged if installed incorrectly. Some
lenses will require both screws be in one
slot.
The “D” screw has a fold out clip for
hand tightening. A screwdriver slot is also
included on the screw.
Do not insert any object as leverage into the
“D” clip as it will damage screw and void
warranty.
A lens may have 1/4” and / or 3/8” threaded
holes. (1) 3/8” and (2) 1/4” screws are
included with each lens plate. It is important
to use the correct size.
Mounting holes
Attaching lens plate to lens
Attaching lens to Pan-Tilt Head AS
Pan-Tilt Head AS Features
Front View
Arca-Swiss style
quick release
Innovative Camera Supports
Pan lock knob
(rotate counter-clockwise
to tighten)
Attach the Pan-Tilt Head AS to the tripods’ ⅜”-16 mounting stud and tighten until firmly attached.
* * * * * Caution * * * * *
If you are using a tripod with a ¼”-20 mounting stud, you will need to purchase a ⅜” to ¼” reducer
bushing and install it in bottom of the Pan-Tilt Head’s base.
Attaching the Pan-Tilt Head AS to a tripod
For a period of five (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any
defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any
modifications made by the customer. Excessive force unscrewing knobs will void warranty. Warranty service is
available by returning the Pan-Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a
return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a
copy of the sales receipt.
USA 5 Year Warranty
Repair service is available by returning the Pan-Tilt Head AS (shipping prepaid) to Custom Brackets.
All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter
explaining the problem, and a copy of the sales receipt. A repair cost will be issued and must be approved
prior to any repairs. Shipping charges are the responsibility of the customer.
Repair
The Pan-Tilt Head AS is designed completely maintenance-free.
Maintenance
For a period of five (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any
defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any
modifications made by the customer. Excessive force unscrewing knobs will void warranty. Limitation to the
warranty - after year one shipping charges are not covered. Warranty service is available by returning the Pan-
Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number
(email [email protected] to obtain), letter explaining the problem, and a copy of the sales receipt.
International 5 Year Limited Warranty
The Pan-Tilt Head AS has many unique features. It is constructed from anodized aluminum for a lightweight
and scratch-resistent finish. The Pan-Tilt Head has separate lock and drag knobs for better control. All knobs
are captive to prevent loss. All of the fasteners are stainless steel to resist corrosion and black oxide for
appearance.
Pan-Tilt Head AS Features
Indexing the quick release to accept a camera
Using the supplied allen wrench (3/16”), remove
screw from the top of the quick release, then lift
the quick release off the Pan-Tilt Head.
Align quick release far right image (Camera Setup)
and align pins using pin holes #1 & #2 (see below)
in top of the tilt head. Once in place, install screw
into the top of the quick release of the Tilt Head.
For Long Lens Setup, use pin holes #2 & #3.
Long Lens
Setup
Camera
Setup
Top view of Pan-Tilt Head
(quick release removed)
Hole #2
Hole #3
Hole #1