Vaddio PreVIEW Dual 6.4 Monitor User Manual
Page 2
PreVIEW Dual 6.4
©2006 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing subject to
change. Vaddio and PreVIEW are registered trademarks of Vaddio. Document 111506-64 Rev.
B.
Intended Use:
Before operating the Vaddio PreVIEW Series LCD Rack Mount Monitors, please read the documentation thoroughly. The systems were
designed, built and tested for use indoors, and with the provided power supply. The use of a power supply other than the one provided or
outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.
Save These Instructions:
The information contained in this manual will help you install and operate your PreVIEW system. If these instructions are misplaced, Vaddio
keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the Vaddio
website. These documents can be downloaded from
www.vaddio.com
free of charge.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In this case, a
Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other
liquids and avoid extremely humid conditions and environments.
The LCD panels are covered with a thin protective film. Remove this film by carefully lifting the film at a corner and carefully peel back.
Do not scratch or apply pressure to the LCD surface. Scratched, cracked or broken LCD panels are not covered under warranty.
Use all four screws when racking the PreVIEW series monitors. The tilting mechanism requires four screws for proper operation.
The video inputs are 75 ohm and the looping outputs are active and require power to output the signal.
FCC Part 15 Compliance and CE Declaration of Conformity
FCC Part 15 Compliance
This product is herewith confirmed and found to comply with the requirements set up by ANSI C63.4 & FCC PART 15 regulations for the
evaluation of electromagnetic compatibility. This Device complies with Part 15 of the FCC rules Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) This device must accept any interference including interference that may
cause undesired operation of the device.
Standards:
FCC Part 15:2005, Subpart B, Class B
ANSI C63.4:2003
CISPR 22:1997+A1:2000+A2:2002
CISPR 16-1:2003
European Compliance
This product meets the requirements for the below standards and hence fulfills the requirements of the EMC Directive 89/336/EEC as
amended by Directives 92/31/EEC and 93/68/EEC within the CE Marking Requirement.
Standard(s) To Which Conformity Is Declared:
EN55022: 1998+A1:2000+A2:2003 Class B
EN61000-3-2: 2000
EN61000-3-3: 1995+A1:2001
EN55024: 1998+A1:2001+A2:2003
IEC61000-4-2: 1995+A1:1998+A2: 2000
IEC61000-4-3: 2002
IEC61000-4-4: 2004
IEC61000-4-5: 1995+A1:2000
IEC61000-4-6: 1996+A1:2000
IEC61000-4-8: 1993+A1:2000
IEC61000-4-11: 1994+A1:2000
HARDWARE WARRANTY:
Please see the Vaddio website at
http://www.vaddio.com
for the Vaddio Statement of Warranty for all Vaddio Products. The Statement of
Warranty covers the policies and procedures of the Hardware Warranty, Exclusions, Customer Service, Technical Support, Return Material
Authorizations (RMA), Voided Warranty, Shipping and Handling and Products Not Under Warranty. The Vaddio Warranty Statement
supercedes all other published warranty statements in content and coverages. Vaddio Technical Support can be contacted through the
Vaddio website or through e-mail support at
mailto:[email protected]
.
Toll Free: 800-
572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
www.vaddio.com
Use only the power supply provided with the PreVIEW system. Use of any unauthorized power supply will void any
and all warranties.