Vaddio Sony BRC-300 - Manual (Page 9)

9
Command Set Command Command Packet Comments
AddressSet Broadcast 88 30 01 FF Address Set
IF_Clear Broadcast 88 01 00 01 FF I/F Clear
CommandCancel 8x 2p FF p: Socket No (=1 to 2)
CAM_Power On 8x 01 04 00 02 FF Power On/Off
Off 8x 01 04 00 03 FF
CAM_Zoom Stop 8x 01 04 07 00 FF
Tele(Standard) 8x 01 04 07 02 FF
Wide(Standard) 8x 01 04 07 03 FF
Tele(Variable) 8x 01 04 07 2p FF p (=0:Slow to 7:Fast)
Wide(Variable) 8x 01 04 07 3p FF p (=0:Slow to 7:Fast)
Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position*
CAM_DZoom On 8x 01 04 06 02 FF Digital Zoom On/Off
Off 8x 01 04 06 03 FF
Combine Mode 8x 01 04 36 00 FF OPT/Digital Zoom Combined
Separate Mode 8x 01 04 36 01 FF OPT/Digital Zoom Separate
Stop 8x 01 04 06 00 FF
Tele(Variable) 8x 01 04 06 2p FF p (=0:Slow to 7:Fast)
Wide(Variable) 8x 01 04 06 3p FF p (=0:Slow to 7:Fast)
Direct 8x 01 04 46 00 00 0p 0q FF pq: Digital Zoom Position*
CAM_Focus Stop 8x 01 04 08 00 FF
Far(Standard) 8x 01 04 08 02 FF
Near(Standard) 8x 01 04 08 03 FF
Far(Variable) 8x 01 04 08 2p FF p (=0:Low to 7:High)
Near(Variable) 8x 01 04 08 3p FF p (=0:Low to 7:High)
Direct 8x 01 04 48 0p 0q 0r 0s FF pqrs: Focus Position*
Auto Focus 8x 01 04 38 02 FF AF ON/OFF
Manual Focus 8x 01 04 38 03 FF
Auto/Manual 8x 01 04 38 10 FF
One Push Trigger 8x 01 04 18 01 FF One Push AF Trigger
Infinity 8x 01 04 18 02 FF Forced Infinity
CAM_AFMode Normal AF 8x 01 04 57 00 FF Normal AF Mode
Interval AF 8x 01 04 57 01 FF Interval AF Mode
Zoom Trigger AF 8x 01 04 57 02 FF Zoom Trigger Mode
Active/Interval Time 8x 01 04 27 0p 0p 0q 0q FF pp: Active Time qq: Interval Time
CAM_ZoomFocus Direct 8x 01 04 47 0p 0q 0r 0s pqrs: Zoom Position*
0t 0u 0v 0w FF tuvw: Focus Position*
CAM_WB Auto 8x 01 04 35 00 FF Normal Auto
Indoor 8x 01 04 35 01 FF Indoor Mode
Outdoor 8x 01 04 35 02 FF Outdoor Mode
One Push WB 8x 01 04 35 03 FF One Push WB Mode
Manual 8x 01 04 35 05 FF Manual Control Mode
One Push Trigger 8x 01 04 10 05 FF One Push WB trigger
BRC-300/P Commands
BRC-300/P Command List (1/4)
* See the section under VISCA Command Setting Values.