Vaddio WideSHOT WallVIEW USB - Manual (Page 34)

WideSHOT WallVIEW USB System
WideSHOT WallVIEW USB Document Number 342-0696 Rev. B Page 34 of 44
A PPENDIX 2: C OMMUNICATION S PECIFICATION FOR THE W IDE SHOT
Communication Speed: 9600 bps (default)
Start bit: 1
Stop bit: 1
Data bits: 8
Parity: None
No Flow control
NOTE: The Vaddio WideSHOT Control Protocol is similar, but not identical to the Sony® VISCA™ command set
in order to be compatible with several popular control devices. Not all VISCA commands are supported and
there are many WideSHOT specific commands in the following Command and Inquiry Lists.
WideSHOT Command List (1/2)
Command Set Command Command Packet Comments
Address Set Broadcast 88 30 01 FF Address Set (Daisy chain)
IF_Clear Broadcast 88 01 00 01 FF IF Clear
Command Cancel 8x 2p FF p:socket number(1,2)
CAM_Power On
Off(Standby)
8x 01 04 00 02 FF
8x 01 04 00 03 FF Power On/Off
CAM_WB Auto
Manual
8x 01 04 35 00 FF
8x 01 04 35 05 FF Normal Auto
Manual White Balance
CAM_RGain Reset
Up
Down
Direct
8x 01 04 03 00 FF
8x 01 04 03 02 FF
8x 01 04 03 03 FF
8x 01 04 43 00 0p 0q 0r FF
pqr: Red (0x0-0x010) Default 8
CAM_BGain Reset
Up
Down
Direct
8x 01 04 04 00 FF
8x 01 04 04 02 FF
8x 01 04 04 03 FF
8x 01 04 44 00 0p 0q 0r FF
pqr: Blue (0x0-0x010) Default 8
CAM_AE Full Auto
Manual
8x 01 04 39 00 FF
8x 01 04 39 03 FF Auto Exposure Mode
Manual Control Mode
CAM_Aperture Reset
Up
Down
Direct
8x 01 04 02 00 FF
8x 01 04 02 02 FF
8x 01 04 02 03 FF
8x 01 04 42 00 0p 0q 0r FF
pqr: Sharpness (0x0-0x010) Default 8
CAM_Bright Reset
Up
Down
Direct
8x 01 04 0D 00 FF
8x 01 04 0D 02 FF
8x 01 04 0D 03 FF
8x 01 04 4D 00 00 0p 0q FF
pqr: Bright (0x0-0x0010) Default 8
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs:0x0000 – 0xFFFF
Tally On
Off
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
BLK.Enhance Pedestal 8x 01 7E 53 00 0p 0q 0r FF pqr: Contrast (0x0-0x010) Default 8
CRM.Enhance Chroma 8x 01 7E 55 00 0p 0q 0r FF pqr: Saturation (0x0-0x010) Default 8
DNR.Enhance Noise Reduction 8x 01 7E 58 00 0p 0q 0r FF pqr: Noise reduction (0x0- 0x010)
Default 0
AGC.Enhance AGC Mode 8x 01 7E 59 00 FF
8x 01 7E 59 01 FF
8x 01 7E 59 02 FF Low
Auto Default
High
CAM_Shutter Reset
Up
Down
Direct
8x 01 04 0A 00 FF
8x 01 04 0A 02 FF
8x 01 04 0A 03 FF
8x 01 04 4A 00 00 00 0p FF
p: Shutter Speed (0-8) Default 8
Pin # RJ-45 RS-232 and IR Out Pins
1) Unused
2)
Unused
3) Unused
4)
IR Output (Diff Signal to Quick-Connect SR Only)
5) IR Ground (Diff Signal to Quick-Connect SR Only)
6) GND (GND of IR Short Range - Pin 3)
7) RXD (from TXD of control source)
8) TXD (to RXD of control source)
12345678