Silverline Pressure Washer 1400W - Manual (Page 8)

www.silverlinetools.com
7
Notes:
• A typical pattern of use for using detergent foam would be to first clean
with water to remove light surface deposits, then apply detergent foam
and finally, rinse off with clean water
• Detergent foam requires a few minutes to work when applied to
surfaces. Normally for maximum cleaning leave 2-5 minutes between
applying foam and removing with clean water – this is an ideal
opportunity to brush/scrub the surface where most dirt has collected. Do
not allow foam to dry on the surface, for instance, on a hot day, when
there may be limited time between dispensing foam and rinsing off,
depending on the surface
• Do not use detergents which are not designed for pressure washers.
They may contain chemicals that could damage seals
• Read the instructions provided with the detergent thoroughly -
especially if concentrated. Diluting to the detergent manufacturer’s
recommendations will ensure effective cleaning without using excessive
detergent
Switching off
When you have finished using the machine, always carry out the following
steps:
1. Switch off the machine and disconnect from the mains supply
2. Turn off the water supply
3. Squeeze the trigger and allow all residual water pressure to bleed
4. Disconnect the water supply
5. Drain all water from the machine and hoses, and store in a dry place
Warning: Do not switch off the water supply before turning off the pump as
the pump must not be run without water.
Warning: Never disconnect the high pressure hose at either end without
depressurising first
Accessories
A range of accessories is available from your Silverline stockist to
enhance the functionality of your pressure washer, including brushes and
replacement or higher specification parts.
www.silverlinetools.com
7
1400W Pressure Washer 101389
Operating Instructions
Switching on
• Always open the water supply tap before switching on to protect the
pump from damage
• Set the Trigger Lock-Off Lever (9) to prevent the Trigger (11) being
pressed
• Connect the pressure washer to the mains supply and turn the On/Off
Switch (26) on. The pump operates immediately to build up pressure and
each time the trigger is pressed to restore water pressure
• It is important that all air is bled from the hoses and lance before using
the pressure washer. Disable the lock-off lever and squeeze and hold the
trigger until water is sprayed in a steady stream. This may take up to 2
minutes or possibly longer on first use
Using your pressure washer
• To spray water, squeeze the Trigger (11). Make sure you are holding the
lance securely as there will be a small recoil action on start-up
• To disable the trigger use the Trigger Lock-Off Lever (9) when necessary
• The Nozzle & Pattern Selector (5) can be adjusted between a wide
fan pattern (60°), and a strong narrow jet by rotating. It is advisable to
start with the nozzle turned clockwise (fan pattern), and experiment
with narrower patterns, and different spray distances, until the correct
strength is achieved. Release the trigger when changing setting
• Use the Pressure Adjuster (10) to adjust pressure output. Release the
trigger when changing setting
• The pressure washer will protect the motor from over-heating if used
continuously for too long, and will prevent the trigger from operating. It
will reset after cooling for a few minutes. It is recommend to have a
work pattern that prevents the over-heating protection feature activating
by not holding down the trigger continuously
• If you are unsure of the durability of the surface that is being cleaned,
avoid using the narrow jet setting, reduce the pressure and start washing
further away from the surface
• It is recommended to hold the lance at an angle of 45˚ to the surface
being cleaned. This will give maximum control, and most effective
cleaning
• Always test-clean an inconspicuous area first to check that the cleaning
process or detergent will not damage the surface being cleaned,
particularly mortar between bricks or patio slabs, which can be easily
removed with water jet
Using detergent
1. Remove the cap from the Detergent Bottle (1) and fill with a pressure
washer compatible detergent. There are many products available
that are suitable for pressure washers including patio cleaner, glass
cleaner, car shampoo, traffic film remover, wood and plastic cleaning
solutions, plus general purpose pressure washer detergent
2. The pressure washer is designed to dispense detergent on the low
pressure setting and dispense clear water on the high pressure
setting. The Pressure Adjuster (10) is marked with the required
direction for increasing or decreasing pressure. Adjust the Nozzle &
Pattern Selector (5) to the required setting if necessary. Release the
trigger when changing either of these settings
NOTE: The detergent ratio is variable depending on the pressure adjuster
setting.
3. Once you have finished using detergent, set the lance to the high
pressure setting on the pressure adjuster, and spray until the water is
clear
101389_Z1MANPRO1.indd 7 09/08/2013 10:44