SawStop T-Glide - Manual (Page 2)

SawStop Service
Department
503-582-9934
www.sawstop.com
© SawStop, LLC
17 19
16 14
12
21
18
11 13
15
parallelism
adjustment
screw parallelism
adjustment
screw
• Press down on the fence handle to clamp the fence to the front
tube. If the fence does not clamp tightly enough to hold its
position against a moderate amount of force, you can increase
the clamping pressure by turning both parallelism adjustment
screws clockwise using a 5 mm hex key. Those screws are
located in the vertical edge of the fence cross-bracket.
Alternatively, if too much force is required to push the
fence handle down to clamp the fence to the front tube,
you can reduce the clamping pressure by turning both
parallelism adjustment screws counter-clockwise.
Congratulations, your fence system is now
installed and ready to use.
Other Accessories
There are optional accessories
available for your saw, such as a
mobile base or an out-feed table.
See your saw Owner’s Manual
for more information.
gap
• Once the fence is tightly clamped to the front tube, move the
left end of the tube back toward the saw until there is only a
small gap (approximately 1/16 inch) between the front rail and
the rear of the fence. Tighten the left-most M8 x 16 hex head bolt
that holds the tube to the front rail using a 13 mm wrench.
gap
• Next, move the fence to the right end of the tube, repeat the
above process to position the tube, and tighten the right-most
screw. Once both ends of the tube are adjusted correctly, tighten
the remaining M8 x 16 hex head bolts to mount the front tube
to the front rail. The fence should now slide smoothly along the
front tube without binding and without excessive play.
Please refer to your T-Glide Fence System - Professional Series II Owner’s Manual
for information on how to correctly use and adjust your fence system.
adjust the position of
the foot and tighten
the hex nut
• Turn the foot on the bottom of each support leg to adjust its
position until it is in solid contact with the ground. Once the foot
is in contact with the ground, fully tighten the hex nut against the
bottom of the leg using a 13 mm wrench.
• Locate the fence and the red fence handle. Thread the handle
into the cam lock on the front of the fence.
SawStop
thread the handle into
the cam lock
• Locate the two support legs and remove the two feet from
the T-Glide Table Hardware Pack along with two M8 hex nuts .
Thread an M8 hex nut onto the threaded shaft of each foot so
that the nut is close to the rubber base, and then thread the foot
into the bottom of the support leg as far as possible.
19
21
21
19
6
4
• The holes in the bottom of the front rail are oversized to allow
you to adjust the position of the tube on the rail. To set the tube
in the correct position, first pull the front tube away
from the table as far as possible. Next, place your
fence down on the tube near the left end.
• Use a straight-edge to level the front edge of the extension
table to the saw table. You may have to pull up or push down on
the extension table to level it. Once the front edge of the extension
table is level, use a 5 mm hex key and a 13 mm wrench to fully
tighten the nuts on the bolts along the front rail. Repeat the
process to level the rear edge of the extension table. Also fully
tighten the bolts that attach the leg support brackets to the front
and rear rails (bolts in step 8). 16
• Attach each support leg to the corresponding leg support
bracket with an M10 x 40 hex head bolt , two M10 washers ,
and an M10 lock nut and fully tighten the bolts using two
17 mm wrenches. Note that the leg support brackets align with
different holes in the front and rear legs because the brackets
are at different elevations.
25
23 24
• Place the straight-edge lengthwise across the middle of the
table (see Fig. 15a) and level the middle of the extension table
by turning the screw in the adjustment bracket with a 5 mm hex
key (see Fig. 15b).
Fig. 15b
22
17
18
19
support leg
• The support legs attach to the outer ends of the rails and
extension table with M8 x 65 countersunk socket head bolts .
Align the top hole in one support leg with the outermost hole in
the front rail, and the top hole in the second support leg with
the outermost hole in the back rail. Make sure the legs are
positioned against the inside of the extension table. Insert an
M8 x 65 bolt through the holes in the rails, extension table
and legs. Place an M8 washer and an M8 lock washer on
the threaded end of each bolt and then thread an M8 hex nut
onto each bolt. Hand tighten the nuts; do not fully tighten them.
17
22
18
19
22
rear rail
25
24
23
24
front rail
23 24 24
25
Fig. 15a
22
straight-edge
®
Contractor Saw SawStop
Installing Your T-Glide Fence System on Your TM
20
• Locate the front tube and the T-Glide Rails Hardware Pack. If
you have a 36” fence system, remove seven M8 x 16 hex head
bolts and seven M8 lock washers
from the T-Glide Rails Hardware Pack.
If you have a 52” fence system, remove
nine M8 x 16 hex head bolts and nine
M8 lock washers from the T-Glide
Rails Hardware Pack. Position the tube
on the front rail with the rulers facing up
and the 12-inch ruler on the left. The powder coated surfaces of
the tube and rail can be slick, so be careful that the tube does
not fall off the rail. Align the holes in the rail with the holes in the
bottom of the tube. Place an M8 lock washer on each M8 x 16
hex head bolt and insert the bolts through the rail and into the
threaded holes in the bottom of the tube. Hand tighten the bolts;
do not fully tighten them.
6 4
6
4
front tube
0 15 30
45
SawStop 10” Contractor Saw
SA WSTOP
adjustment screw
T-Glide Rails Hardware Pack
2 Countersunk Socket Head Bolts, M8 x 25 (8)
Washers, M8 (8) 3
Lock Washers, M8 (17) 4
II Professional Series
Countersunk Socket Head Bolts, M8 x 16 (8) 1
Hex Head Bolts, M8 x 16 (9) 6
Hex Nuts, M8 (8) 5
F
Fold line
Height = 664 mm
332 mm
straight-edge
16 make sure to tighten the bolts that
attach the leg support brackets to
the front and rear rails