Aqua Bath IS413684SH-OT-FUS mod 4 - Manual (Page 2)

ACCESSIBLE SERIES (Open Top)
•
Model IS413684SH-OT-FUS mod 4”-L valve on left.
• Model IS413684SH-OT-FUS mod 4”-R valve on right.
• Bath units designed for hospitals, nursing homes, rehabilitation
centers, hotels, motels and residential applications.
• Acrylic one-piece molded construction simplifies installation.
• Inside dimensions: 36” W x 36” D x 78” H.
• Can be furnished complete with valve, hand held shower set,
curtain and hooks.
• 4” threshold, also available with 7 3/4” threshold.
• 24” vertical grab bar and two (2) 18” horizontal grab bars.
• Vacuum-formed from .1875” one-piece sanitary grade acrylic.
For additional information, call the
Aqua Bath Customer Service
Department At 1-800-232-2284
The IS413684SH-OT-FUS mod 4” is
NOT ADA compliant. Please see Aqua
Bath’s full line of ADA compliant shower
and tub/shower units. Please check with
your local city and state for code
compliancy. Aqua Bath accepts no
responsibility for final code compliance.
• Manufacturing Tolerance Of (±1/4”) Due To The Nature
Of The Materials Used.
Open Top Acrylic Shower Stall
The shower enclosure shall be Aqua Bath model IS413684SH-OT-FUS mod 4” acrylic and be molded from a single sheet so as
not to have any joints or seams, shall meet ANSI Z124.2. Unit shall have a backside flame spread of less than 30 (Class B).
Shall be designed to be NAHB LISTED.
The enclosure shall have inside dimensions of 36” W x 36” D x 78” H and outside dimensions of 41” W x 37” D x 84” H.
Outside dimensions to the top nailing flanges of the unit are 38½” left to right and 37¼” front to back.
A soap tray is molded on the valve wall corner 52” above the shower floor. The approximate weight of the unit shall be 230lbs.
The unit shall be formed with a patented recessed trench system so as to direct water to the center drain.
Standard Accessories:
1) Two 18” x 1½” diameter horizontal grab bars and one 24” vertical grab bar, fabricated from 18 gauge stainless steel with 1½”
safety statute clearance, mounted with stainless steel bolts and secured from the rear with 3” x 3” x 11 gauge metal mounting
plates. 2) 28” rectangular shaped phenolic fold-up seat. 3) 1” diameter, 18 gauge stainless steel curtain rod. After grab bars and
curtain rod have been factory installed, they will be sealed from the backside making the unit completely waterproof.
4) Ribbed bottom for slip resistance (standard).
5) Self-caulking brass drain (fits 2” pipe) with stainless steel strainer and drain is to be field installed.
Available Accessories:
1) Molded-in integral seat in lieu of factory installed fold-up seat.
2) Hand held shower set (includes 60” flex hose, swivel connector, brass nipple, lock nut, wall outlet and vacuum breaker).
3) 24” slide bar, 30” slide bar or two (2) wall brackets installed on valve wall for use with hand held shower set.
Note: The determination of the use of slide bar or wall brackets to be installed in the unit is based upon the valve package
chosen by the specifier for use in the unit. Aqua Bath recommends the use of a slide bar as an accessory in the unit rather
than the use of a glide bar / glide rail.
4) Pressure balance or thermostatic control valve. 5) Shower curtain - antibacterial, with hooks.
6) Weighted shower curtain (patented), antibacterial, with hooks. 7) Seat belt (for the fold-up seat only).
8) Dome light (must be field installed and light shipped separately from unit).
9) ASTM F462 non-slip bottom. (*) When the ASTM F462 bottom is specified with the center drain location,
it will re-configure the trench drain system. A signed off approval is required for the bottom re-configuration.
Received and / or approved by:
Name:______________________________
Company:___________________________
Title:_______________________________
Phone:______________________________
Date:_______________________________
Modifications:
03/09
AQUA BATH COMPANY INC.921 Cherokee Ave.Nashville, TN 372071-800-232-2284Fax (615) 227-9446
 www.aquabath.com 