Graymills Bed Filter Magnetic Seperator OMI - Manual (Page 4)

WARRANTY
Graymills Corporation warrants that the equipment manufactured
and delivered, when properly installed and maintained, shall be free
from defects in workmanship and will function as quoted in the
published specification. Graymills does not warrant process per-
formance, nor assume any liability for equipment selection, adapta-
tion, or installation.
Warranty does not apply to damages or defects caused by shipping,
operator carelessness, misuse, improper application or installation,
abnormal use, use of add-on parts or equipment which damages or
impairs the proper function of the unit, and modifications made to
the unit.Warranty does not apply to expendable parts needing
replacement periodically due to normal wear and tear.
A new Warranty period shall not be established for repaired or
replaced materials or products. Such items shall remain under
Warranty for only the remainder of the Warranty period of the
original material or product.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL
OTHER WARRANTIES, WHETHER ORAL, WRITTEN,
EXPRESSED, IMPLIED OR STATUTORY. GRAYMILLS COR-
PORATION MAKES NO OTHER WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE WHICH EXCEED THE AFORESTATED OBLIGA-
TION ARE HEREBY DISCLAIMED BY GRAYMILLS COR-
PORATION AND EXCLUDED FROM THIS SALE. Graymills
warranty obligations and Buyer remedies (except to title), are sole-
ly and exclusively stated herein. In no case will Graymills be
liable for consequential damages, loss of production, or any other
loss incurred due to interruption of service.
Graymills’ obligation under this Warranty shall be limited to:
(a) Repairing or replacing (at Graymills sole discretion) any non-
conforming or defective component within one year from the
date of shipment from Graymills.
(b) Repairing or replacing (at Graymills sole discretion), compo-
nents supplied by, but not manufactured by Graymills, to the
extent of the warranty given by the original manufacturer.
Buyer must give Graymills prompt notice of any defect or failure.
If you believe you have a Warranty claim, contact Graymills at
(773)248-6825. Any returned material must have an RMA number
on the outside of the package and shipped prepaid or shipment will
be refused. Graymills will promptly examine the material and
determine if it is defective and within the Warranty period.
Graymills Corporation 3705 N. Lincoln Avenue Chicago, IL 60613-3594 (773) 248-6825 FAX (773) 477-8673 www.graymills.com
REPLACEMENT ITEMS
Part Number Description
785-09818 25W Gear Motor for BF40/MS40
785-09819 10X Reducing Gear for BF40/MS40
785-09820 90X Reducing Gear for BF40/MS40
785-90040 40W Gear Motor for BF80/MS80
785-90041 10X Reducing Gear for BF80/MS80
785-90042 90X Reducing Gear for BF80/MS80
785-90521 Replacement Motor for MS40
785-90522 Replacement Motor of MS80
785-09821 Float Switch (BFCT40 and BFCT80)
IMV08 Pump for BFCT40
IMV25 Pump for BFCT80
785-09905 Replacement Mesh Chain for BF40
785-90406 Replacement Mesh Chain for BF80
785-90421 Repair Clips for Chain
742-90152 20 micron Filter Paper, 150 yd roll
and roller so that it does not harden and cause a mal-
function. Clean away metal chips as necessary.
• If the Magnetic Separator will not be used for an
extended period of time, loosen the wing nuts to
decrease pressure of the scraper on the roller. This will
extend roller life.
• Empty and clean the unit as necessary. Check the dif-
fuser tray, chain and tank. Wipe out all debris with a
rag.
• To prolong finish quality, wipe off the exterior of the
machinery with a clean, damp cloth as needed.
Figure 2
Wiring diagram for Full System
Figure 3
Wiring diagram for Magnetic Separator
TRANSFORMER
480V
110V
0V
120V 240V
0V
FUSE 2A
LIMIT SWITCH
1 2
OVER RELAY
3 MAG
SEP
MAGNETIC
SWITCH
4
W
2
U
2
V
2
U
1
V
1
W
1
230V
RED BLUE BROWN
BLACK YELLOW WHITE
W
2
U
2
V
2
U
1
V
1
W
1
460V