Audiovox ACD85 - Manual (Page 6)

OPER OPER OPER OPER OPERA A A A AT TT TTING INSTRUC ING INSTRUC ING INSTRUC ING INSTRUC ING INSTRUCT TT TT IONS IONS IONS IONS IONS
6 6 6 6 6
OPEROPEROPEROPEROPER
AAAAA
TTTTT
ING INSTRUCING INSTRUCING INSTRUCING INSTRUCING INSTRUC
TTTTT
IONSIONSIONSIONSIONS
1 1 1 1 1
POWER ON/OFF AND DIM BUTTON
Momentarily press this button to turn the unit on; the
icon appears on the display. Press the button
for at least 2 seconds to turn the unit off. If the ignition
switch is “on”, the unit will also turn on automatically
when a compact disc is inserted, or if any other front
panel control button is pressed. While the unit is on,
each time the button is momentarily pressed and
released, the VFD display panel backlighting intensity
will change from low-to-medium-to-high, and then
back to low, thereby providing three different intensity
settings.
2 2 2 2 2
AUDIO CONTROL (VOL +/- ) BUTTONS
To increase the volume level, press the + button. The
volume will increase and the level will be shown on
the display panel from a minimum of VOL 00 to a
maximum of VOL 100. To decrease the volume level,
press the - button. The display will automatically
return to the normal indication 5 seconds after the last
volume adjustment or when another function is
activated. These control buttons are also used in con-
junction with the Select (SEL) button
3
to adjust the
bass, treble, balance and fader levels as described
in
4
,
5
,
6
and
7
.
3 3 3 3 3
SELECT (SEL) CONTROL BUTTON
This button is used to select the audio function
(volume, bass, treble, balance, or fade) whose
setting is adjusted using the AUDIO CONTROL
buttons
2
. Pressing the SEL button once will set the
unit for volume adjustment (VOL will appear on the
display panel) and an audible beep will occur. Press-
ing the button additional times will select bass
adjustment (BAS will appear on the display panel),
treble adjustment (TRE on the display), balance
(BAL), or fader (FAD). The display will automatically
return to the normal indication 5 seconds after the the
last adjustment or when another function is activated.
NOTE: Regardless of the Preset Equalizer setting,
whenever Base, Treble, Balance or Fader
settings are adjusted, the Equalizer setting
will always return to FLAT mode.
4 4 4 4 4
BASS CONTROL
To adjust the bass level (Equalizer function inactive),
first select the Bass mode by pressing the SEL button
so the BAS indication appears on the display panel.
Within 5 seconds of choosing the Bass mode,
press the VOL - button to decrease the bass
response, or the VOL + button to increase it as
desired. The level will be shown on the display panel
from a minimum BAS -10 to a maximum of BAS +10
(BAS 00 indicates flat response). The display will
automatically return to the normal indication 5 seconds
after the last adjustment or when another function is
activated.
TUNER
15
29 26, 40 24, 41 25, 42
14 13
3
4
5
6
7
2
9 30 16 20 21(FAR SIDE)
32
33,34
(FAR SIDE)
19 18, 35
31
11
22
23
17
1
12 8, 10 28
SCAN
PRESET
UALIZER
REL
(AUX)
MODE
OPEN
LOUD DISC-DN DISC-UP
DIM
SEL
VOL TUN
3 DISP BAND 2 1 4 5 6 AMS
PAUSE SCAN REPEAT SHUFFLE
LO/DX MUTE
MONO
LOUD
ST
TUNER CD TAPE IN PTY MTL EON
AF TA TP
38
39
36 37
27(FAR SIDE)