Arcam CD73 - Manual (Page 6)

CD73
6
English
CD73
7
En
gl
is
h
Using the CR224 remote control
DISP (Display)
Turns the display on or off. Turning the display off
generally produces a slight improvement in sound
quality.
A–B
This button enables you to repeat any section of
music within a track. Whilst the disc is playing, press
the
A–B button at the start of the section you wish
to repeat. ‘REPEAT’ is shown on the display and the
letter ‘A–’ flashes. Press the button a second time
when you reach the end of the section you wish to
repeat. The ‘A–B’ letters stop flashing and remain
lit. This section will repeat until you press or
or
. The forward search button ( ) moves forward
within the selected loop.
REPEAT
To repeat the entire CD or a pre-programmed
selection of tracks press
REPEAT once: ‘REPEAT’
lights on the display. To repeat a particular track,
select that track and then press
REPEAT twice so
that ‘REPEAT 1’ is shown on the display. If you now
select a different track, that track is repeated
instead.
To cancel the repeat function press
REPEAT a third
time.
TIME
Press TIME once to display the remaining time of the
currently playing track. Press again to display the
time remaining on the disc. Press a third time to turn
the text display on.
Press TIME again and the display reverts to its
original setting, showing the time elapsed for the
current track.
For CDs with text, pressing TIME once while the disc
is loaded but not playing displays the artist’s name.
Pressing TIME a second time displays the total
number of tracks and the total playing time.
0–9 keypad
This allows direct access to individual tracks on
the disc. To select a track, press the corresponding
keypad button. For tracks greater than 9, enter the
digits in sequence. For example, to play track 15,
press and hold
1 until the number on the display
moves to the left, then press 5 .
PROG (Program)
You can program a selection of up to 24 tracks
from a disc to play in any order. Select a track by
using the
and buttons, then press PROG to
program the track into memory (‘PROGRAM’ appears
on the display to indicate that you have started
programming a sequence). Repeat these steps to
program the remaining tracks in your selection.
Alternatively, press PROG once and enter your track
selection using the 0–9 keypad.
The display shows the track numbers programmed,
the total length of the programmed sequence and
the number of tracks programmed (shown by a
number below the word ‘STEP’).
Each time you enter a track the number below ‘STEP’
increments by one and flashes until you press PROG
to confirm. If you fail to press PROG within about five
seconds the display stops flashing and you will have
to reselect the track.
Press to play the program. Press again to replay
the entire sequence from the start. Press PROG
again to exit the program facility: the display flashes
‘CONTINUE’ and shows ‘0’.
MUTE
Stops sound to the speaker outputs of certain Arcam
amplifiers.
VOL (Volume) +/–
Adjusts the volume on Arcam remote-controllable
amplifiers.
Note that the volume (+/–) controls and
MUTE
button have no effect on the audio output level of the
CD players.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the display area
on the CD player (where the IR receiver is located),
or the remote control may not work.
OPEN
Opens and closes the CD tray.
Skip and Search Track
Skip track backwards and forwards; search
backwards and forwards (see page 5)
Playback control
Play, Stop and Pause (see page 5).
SHUFFLE
Press once to shuffle play CD tracks (i.e. play them
in a random order). Press again to cancel shuffle
play.
Source selection
These operate in the same way as the source
selector on the front panel of an Arcam integrated
amplifier.