Pioneer GM-D8601 - Manual (Page 12)

Specifications
GM-D8601
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Current consumption ............ 24 A (at continuous power,
4
W)
Average current drawn ......... 2.9 A (4
W for one channel)
4.0 A (2 W for one channel)
6.0 A (1
W for one channel)
Fuse ................................................ 40 A × 2
Dimensions (W × H × D) ... 265 mm × 60 mm ×
200 mm
Weight .......................................... 2.7 kg (Leads for wiring not
included)
Maximum power output ....... 600 W × 1 (4
W) / 1 600 W ×
1 (1 W)
Continuous power output ... 300 W × 1 (at 14.4 V, 4
W,
20 Hz to 240 Hz,
≦ 1 % THD)
500 W × 1 (at 14.4 V, 2 W,
100 Hz,
≦ 1 % THD)
800 W × 1 (at 14.4 V, 1
W,
100 Hz, ≦ 1 % THD)
Load impedance ...................... 4
W (1 W to 8 W allowable)
Frequency response ............... 10 Hz to 240 Hz (+0 dB,
–3 dB)
Signal-to-noise ratio ............... 100 dB (IEC-A network)
Low pass filter:
Cut off frequency ........... 40 Hz to 240 Hz
Cut off slope .....................
–12 dB/oct
Bass boost:
Frequency .......................... 50 Hz
Level ..................................... 0 dB to 18 dB
Gain control:
RCA ...................................... 200 mV to 6.5 V
Speaker .............................. 0.8 V to 16 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 25 k
W
Speaker .............................. 16 V / 12 k
W
GM-D9601
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Current consumption ............ 39 A (at continuous power,
4
W)
Average current drawn ......... 3.7 A (4
W for one channel)
5.2 A (2 W for one channel)
7.5 A (1
W for one channel)
Fuse ................................................ 40 A × 3
Dimensions (W × H × D) ... 315 mm × 60 mm ×
200 mm
Weight .......................................... 3.3 kg (Leads for wiring not
included)
Maximum power output ....... 1 000 W × 1 (4 W) / 2 400 W
× 1 (1
W)
Continuous power output ... 500 W × 1 (at 14.4 V, 4 W,
20 Hz to 240 Hz,
≦ 1 % THD)
800 W × 1 (at 14.4 V, 2
W,
100 Hz, ≦ 1 % THD)
1 200 W × 1 (at 14.4 V, 1
W,
100 Hz,
≦ 1 % THD)
Load impedance ...................... 4 W (1 W to 8 W allowable)
Frequency response ............... 10 Hz to 240 Hz (+0 dB,
–3 dB)
Signal-to-noise ratio ............... 100 dB (IEC-A network)
Low pass filter:
Cut off frequency ........... 40 Hz to 240 Hz
Cut off slope .....................
–12 dB/oct
Bass boost:
Frequency .......................... 50 Hz
Level ..................................... 0 dB to 18 dB
Gain control:
RCA ...................................... 200 mV to 6.5 V
Speaker .............................. 0.8 V to 16 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 25 k W
Speaker .............................. 16 V / 12 k
W
Notes
! Specifications and the design are subject to
modifications without notice.
! The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn by multiple
power amplifiers.
En
12
Appendix
Additional information