Pioneer VSX-521 - Manual (Page 38)

Additional information 08
38
En
08
Can’t operate the remote control.
 Replace the batteries (refer to page 9).
 Operate within 7 m, 30º of the remote sensor (refer to page 9).
 Remove the obstacle or operate from another position.
 Avoid exposing the remote sensor on the front panel to direct
light.
The display is dark or off.
 Press DIMMER on the remote control repeatedly to return to
the default.
The front panel display switches over for no apparent
reason to various different displays.
 This happens because the demo display is in operation. To
turn off the demo display, press any button to go back to the
original display, or set the
FL Demo Mode to OFF (see The FL
Demo Mode menu on page 34).
The Bluetooth wireless technology device cannot be
connected or operated. Sound from the Bluetooth wireless
technology device is not emitted or the sound is
interrupted.
 Check that no object that emits electromagnetic waves in the
2.4 GHz band (microwave oven, wireless LAN device or
Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop
using the object emitting the electromagnetic waves.
 Check that the Bluetooth wireless technology device is not too
far from the unit and that obstructions are not set between the
Bluetooth wireless technology device and the unit. Set the
Bluetooth wireless technology device and the unit so that the
distance between them is less than about 10 m and no
obstructions exist between them.
 Check that the Bluetooth ADAPTER and the ADAPTER PORT
terminal of the unit are correctly connected.
 The Bluetooth wireless technology device may not be set to the
communication mode supporting the Bluetooth wireless
technology. Check the setting of the Bluetooth wireless
technology device.
 Check that pairing is correct. The pairing setting was deleted
from this unit or the Bluetooth wireless technology device.
Reset the pairing.
 Check that the profile is correct. Use a Bluetooth wireless
technology device that supports A2DP profile and AVRCP
profile.
HDMI
No picture or sound.
 If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer
for support.
No picture.
 Video signals that are input from the analog video terminal
will not output from the HDMI terminal. Signals that are input
from the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
 Depending in the output settings of the source component, it
may be outputting a video format that can’t be displayed.
Change the output settings of the source, or connect using
the component or composite jacks.
 This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the component or composite
video jacks.
 Depending on the connected source component, it’s possible
that it will not work with this receiver (even if it is HDCP-
compatible). In this case, connect using the component or
composite video jacks between source and receiver.
 If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
 To output signals in Deep Color, use an HDMI cable (High
Speed HDMI ® Cable) to connect this receiver to a component
or TV with the Deep Color feature.
The OSD screen (System Setup menu, etc.) isn’t displayed.
 The OSD will not appear if you have connected using the
HDMI output to your TV. Use component or composite
connections when setting up the system.
No sound, or sound suddenly ceases.
 Check that the Audio Parameter setting is set to HDMI AMP/
THRU (refer to page 29).
 If the component is a DVI device, use a separate connection
for the audio.
 HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
 Turning on/off the device connected to this unit’s HDMI OUT
terminal during playback, or disconnecting/connecting the
HDMI cable during playback, may cause noise or interrupted
audio.
Synchronized operation not possible using Control with
HDMI function.
 Check the HDMI connections.
 The cable may be damaged.
 Select ON for the Control with HDMI setting (see HDMI Setup
on page 35).
 Turn the TV’s power on before turning on this receiver’s power.
 Set the TV side Control with HDMI setting to on (see TV’s
operating instructions).
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
Configuration
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
Note
• Depending on the component, audio output may be
limited to the number of channels available from the
connected display unit (for example audio output is
reduced to 2 channels for a monitor with stereo audio
limitations).
• If you want to switch the input source, you’ll have to
switch functions on both the receiver and your display
unit.
• Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
VSX-521_SYXCN_En.book 38 ページ ２０１１年２月９日 水曜日 午後４時６分