Pioneer SC-1223-S User Manual

Page 53

Advertising
background image

53

 

 

 

 

06

Listening to your system

Selecting MCACC presets

! Default setting: MEMORY 1
If you have calibrated your system for different listening positions, you can switch between settings to suit the
kind of source you’re listening to and where you’re sitting (for example, watching movies from a sofa, or playing a
video game close to the TV).

1 Press

to the receiver operation mode.

2 While listening to a source, press MCACC.

Press repeatedly to select one of the six MCACC presets. See

Data Management

on

page 83

to check and man-

age your current settings.

! These settings have no effect when headphones are connected.
! You can also press k/l to select the MCACC preset.

Choosing the input signal

On this receiver, it is possible to switch the input signals for the different inputs as described below.
! This receiver can only play back Dolby Digital, PCM (32 kHz to 192 kHz) and DTS (including DTS 96/24) digital

signal formats. The compatible signals via the HDMI terminals are: Dolby Digital, DTS, PCM (32 kHz to 192
kHz), Dolby TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTS-HD Master Audio and SACD.

! You may get digital noise when an LD, CD, DVD or BD player compatible with DTS is playing an analog signal.

To prevent noise, make the proper digital connections (

page 23

) and set the signal input to DIGITAL.

! Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with

your DVD player.

1 Press

to the receiver operation mode.

2 Press SIGNAL SEL to select the input signal corresponding to the source component.

Each press cycles through the options as follows:

! AUTO – The receiver selects the first available signal in the following order: HDMI; DIGITAL; ANALOG.
! ANALOG – Selects an analog signal.
! DIGITAL – Selects an optical or coaxial digital signal.
! HDMI – Selects an HDMI signal.

— When the HDMI audio output parameter is set to THROUGH, the sound will be heard through your TV, not

from this receiver.

When set to DIGITAL, HDMI or AUTO (only selected DIGITAL or HDMI), the indicators light according to the
signal being decoded (see

Display

on

page 14

).

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction measures to make sure your sound source arrives at
the listening position in phase, preventing unwanted distortion and/or coloring of the sound.
Phase Control technology provides coherent sound reproduction through the use of phase matching for an opti-
mal sound image. The default setting is on and we recommend leaving Phase Control switched on for all sound
sources.

% Press PHASE (PHASE CONTROL) to switch on phase correction.

The PHASE CONTROL indicator on the front panel lights.

Notes

! Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are ‘in

phase’, they crest and trough together, resulting in increased amplitude, clarity and presence of the sound
signal. If a crest of a wave meets a trough, then the sound will be ‘out of phase’ and an unreliable sound image
will be produced.

! For discs created with standards other than Phase Control, the LFE channel is delayed upon recording in the

first place. Phase Control Plus function corrects for phase shifting on such discs. For instructions on setting
the Phase Control Plus, see

Setting the Audio options

on

page 65

.

! If your subwoofer has a phase control switch, set it to the plus (+) sign (or 0º). However, the effect you can

actually feel when PHASE CONTROL is set to ON on this receiver depends on the type of your subwoofer. Set
your subwoofer to maximize the effect. It is also recommended you try changing the orientation or the place of
your subwoofer.

! Set the built-in lowpass filter switch of your subwoofer to off. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

! If the speaker distance is not properly set, you may not have a maximized PHASE CONTROL effect.
! The PHASE CONTROL mode cannot be set to ON in the following cases:

— When headphones are plugged in.
— When the PURE DIRECT mode is switched on.
— When the HDMI audio output parameter is set to THROUGH in Setting the

Setting the Audio options

on

page

65

.

Advertising
This manual is related to the following products: