BodyCraft BCG-GX - Manual (Page 12)

11
STEP 6 INSTALL TOP CABLE
Pulleys T3 and T5 are mounted to either side of the steel tab. Do not mount both pulleys
to one side. Assemble cables and pulleys simultaneously
1. Grab the threaded end of the Top Cable (87). Run the cable over a Pulley T1 you will mount
at the front of the Top Frame (2) using one 3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon
Nut (124), as shown in Fig T1.
2. Run the cable back to a pulley you will mount on the Front Upright (T2) using one 3/8" X 1-
3/4" Hex Bolt (101) and one 3/8" Nylon Nut (124). Run the cable over top this pulley, exiting
on the underside.
3. Run the cable forward to the Press Arm Support (13). You will mount two pulleys side-by-
side here using one 3/8" X 3" Hex Bolt (99), two 3/8" Washers (116), and one 3/8" Nylon Nut
(124). Route the cable to the top of Pulley T3 (T3 is the pulley on the right side, as if sitting
on the seat), around T3 to underside of T4. T4 is mounted to the Front Upright (3) using one
3/8" X 1-3/4" Hex Bolt (101) and one 3/8" Nylon Nut.
4. Continue routing the cable entering the underside of T4, exiting on top and on then forward
to T5, which is the left side pulley mounted in Press Arm Support (13). Run the cable over
top of pulley T5, exiting on the underside.
5. Route cable to Pulley T6, which you will mount inside the Front Upright (3) using one 3/8" X
3" Hex Bolt (99), two 3/8" Washers (116), two 3/8" ID Bushings (77), and one 3/8" Nylon Nut
(124). Run the cable on the underside of this Pulley T6.
6. Route cable over top of Pulley T7 you will mount in the rear bracket on the Top Frame (2)
using one Longer 3/8" X 2-3/4" Hex Bolt (100) and one 3/8" Nylon Nut (124).
7. Mount a pulley in the closed end of the Adjustable Pulley Block (18) using one 3/8" X 1-3/4"
Hex Bolt (101) and one 3/8" Nylon Nut (124). Hang this Adjustable Pulley Block (18) by
routing the cable to the underside of the pulley as shown in T8. Continue routing the cable
over top of Pulley T9, which you will mount to Top Frame (2) using one 3/8" X 1-3/4" Hex Bolt
(101) and one 3/8" Nylon Nut (124).
8. Then run the cable through the Floating Pulley Block (21). Orient the Floating Pulley Block
(21) with the threaded end up, flat side down. Threaded installed 1/2" Set Screw (111) to
bracket welded on Top Frame (2). Insert a pulley into the Floating Pulley Block (21), making
sure the cable runs to the underside. Secure the pulley using one 3/8" X 1-3/4" Hex Bolt
(101) and one 3/8" Nylon Nut (124). If you purchased option Leg Press at same time, please
orient the Floating Pulley Block (21), with the threaded end down, flat side up as Leg Press
manual.
9. Route the cable over Pulley T11 mounted to the Top Frame (2) using one 3/8" X 1-3/4" Hex
Bolt (101) and one 3/8" Nylon Nut (124).
10. Run the cable through the looped end of the selector pin lanyard, and then screw the
threaded end of the top cable into the top plate, about half way down. The threaded end of
the cable is an adjustment point but should always have at least one third of the threads
screwed into the top plate.