Neff T69S86N0 - Manual (Page 6)

6
For position of the inlet connection refer Preparing to install.
Use pipe compound or thread sealant, properly threaded pipes
and careful assembly procedure so that there is no cross
threading, etc., which might cause damage or leakage.
Make sure that all connections peformed are free of leakage.
The manufacturer does not accept any liability for leakage on
connections performed by the installer or if the L-tube is moved
or twisted.
There are two ways to carry out the connection to the main gas
line:
■
The hotplate can be connected with rigid pipe as specified in
AS/NZS 5601.1
■
Flexible Hose: If installing with a hose assembly, it must
comply with AS/NZS 1869, 10 mm ID, class B or D, no more
than 1.2 m long and installed in accordance with AS/NZS
5601.1.
Ensure that the hose does not contact the hot surfaces of the
hotplate, oven, dishwasher or any other appliance that may
be installed underneath or next to the hotplate. The hose
should not be subjected to abrasion, kinking or permanent
deformation and should be able to be inspected along its
entire length with the cooktop in the installed position. Unions
compatible with the hose fittings must be used and all
connections tested for gas leaks.
The supply connection point shall be accessible with the
appliance installed.
WARNING: Ensure that the hose assembly is restrained from
accidental contact with the flue outlet of an underbench oven.
Before Leaving- Check all connections for gas leaks with soap
and water. DO NOT use a naked flame for detecting leaks.
Ignite all burners both individually and concurrently to ensure
correct operation of gas valves, burners and ignition. Turn gas
taps to low flame position and observe stability of the flame for
each burner individually and all together. Adhere the duplicate
data plate to an accessible location near the hotplate. When
satisfied with the hotplate, please instruct the user on the
correct method of operation. In case the appliance fails to
operate correctly after all checks have been carried out, refer to
the authorised service provider in your area.
It should be expressly noted that we cannot accept any liability
for direct or indirect damage caused by wrong connection,
leakage or improper installation. When being repaired, the
appliance must always be disconnected from the mains supply;
if required, notify our customer service.
Converting the cooktop from Nat. Gas to
Propane Gas
To change injectors
All work involved in installation, setting and adaptation to a
different gas type must be carried out by authorised personnel
from our Service Centre and must comply with current regulations
and the conditions laid down by the local gas company.
Request change-over injectors from our customer service
deparment (refer injector chart below for sizes).
Before conversion the cooktop must be disconnected from the
electricity and gas valves must be turned to the OFF position.
Changing the nozzles of the rapid, semi-rapid
and auxiliary burners on the cooktop
1. Remove the pan supports, burner covers and diffusers.
2. Change the nozzles using the spanner provided by our
Service Centre (code 424699), taking special care to ensure
that the nozzle does not fall when it is removed from the
burner or when fitted.
Ensure that it is completely tightened in order to guarantee
the seal.
Note: it is not necessary to adjust the primary air control on
these burners.
Changing double flame burner tips
The glass panel and frame are fixed to the rest of the cooktop
using a clip mounting system. The following steps must be
taken to remove the glass panel and frame:
1. Remove all the burner covers and pan supports.
2. Release the front clip fixing the appliance to the kitchen unit
by removing the screw.
3. Loosen the screws on the burners and remove the control
knobs from their respective housings.
Use the disassembly lever 483196 available from our Service
Centre. To release the front clips, apply the lever in the area
shown in figures below according to the cooktop model.
Never use the lever on glass edges which have no trim or
frame!
To release the rear clips, carefully raise the entire glass panel
and frame.
Natural Gas Propane Gas
Burner Hourly Gas
Consumption
(MJ)
Injector
mark
Hourly Gas
Consumption
(MJ)
Injector
mark
Auxiliary 4,80 97 3,50 53
Semi-rapid 8,10 130 6,00 70
Rapid 11,60 157 8,50 83
Wok (inner)
22,00
65
20
47
Wok (outer) 215 115
Distance “Z” 11 12