Barco R9000977 - Manual (Page 47)

7.





5975628J BARCOGRAPHICS 1209S 010797 41
7.14 G2
2 3 2 3 2 3 2 3
I;01*+
,()-. G"#$



G2 ADJUST  
  ENTER ! AB CD"#$
G2 KL#/*¸(o )D/*+23/ ±,-â
.g02ef "#$





 
 
 
      
 !"#
 !"#
 !"#
 !"#
ENTER ! #JAB CD "#2o
uqr;%
&
st/Ý0;}* EXIT ! %&
'(V
VWXdy G$ G2 KL;12S34*{|5
WX8ã G"#$
7.15
4 # 5  6 7 4 # 5  6 7 4 # 5  6 7 4 # 5  6 7
I;01*+
,()-. G"#$


)ï
GAMMA CORRECTIONS ð 
 ENTER ! "#$
I;cA*hij k;KL EÁ"Hš 23/
;)žŸ2 "#$
$ $ $ $%& %& %& %& '( '( '( '(   )*+) )*+) )*+) )*+),,,,- - - -   ./0 ./0 ./0 ./0   123 123 123 1234 4 4 4 5 5 5 56 6 6 6
789: #; 789: #; 789: #; 789: #;<<<<
= = = =    > ?@
A > ?@
A > ?@
A > ?@
A
B C #D !"# B C #D !"# B C #D !"# B C #D !"#<<<<
ENTER ! #J65;7˜2Å_"#2o
pqr;
%&
st/Ý0* EXIT ! %&
'(V
VWXd–EF G$65;7˜UG;1G
34*{|5WX8; 8 C ã9 G"#$
7.16 CRT
" # " # " # " #  $ #  $ #  $ #  $ #    



$  8 $  8 $  8 $  8
CRT % эhˆо*»:+k;V
'„:® 2{r G/á;;ÈÅz7)#$ 1 Uݸ
;»:+kP:® 2{r G/<=*<,
e$2=>5 5 ?Ð ON  5 ?Ð OFF >Z[;»:® 
UG 5 @РAC"#$\; 5 @Р)*B 2 ;»:® 2´
P <,e$2=>"#$e$* CRT ;CD QD
E; ±FGˆ "#$ CRT % 
эhˆо хц /* EXIT ! "#$


  CRT RUN IN CYCLE 
  ENTER ! Hô "#$
»:+k)KL V'„:® 2´P)Q/<=
CRT % * ENTER ! #JHô"#$
:® 2{r GSG<=hij k* CRT 
эhˆо ИЕ#/IJ2)QÁKL'( ID"
#$
I;á
CRT %  ÈÅ G<=*Z[
»:+k;V'„:® A CRT 
эhˆо JHф"#$
SERVICE MODE
Select with or
then <ENTER>
<EXIT> to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
SERVICE MODE
Select with or
then <ENTER>
<EXIT> to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
SERVICE MODE
Select with or
then <ENTER>
<EXIT> to return
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
CRT RUN IN CYCLE
<ENTER> to continue
<EXIT> to cancel
797
A flashing white pattern
will be generated until
<EXIT> is pressed.
The projector only uses
memory blocks adjusted
on an internal # pattern;
if no such block is
available, the projector
can't run the procedure
and leaves the adjustment
mode.
SAFETY
NOTICE
RISK OF ELECTRICAL SHOCK
G2 ADJUSTMENT SHOULD BE
PERFORMED BY BARCO
PERSONNEL, OR BARCO
AUTHORIZED DEALERS.
IF QUALIFIED, PRESS
<ENTER>TO CONTINUE, OR
IF NOT, <EXIT.>TO RETURN.
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE PROJECTOR
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
THE GAMMA CORRETIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOUR ANALYSER!
THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS!