Bushnell NORTHSTAR GOTO 78-8890 - Manual (Page 4)

M
ALIGNING FINDERSCOPE
Look through Main Telescope Tube and establish a well-defined target. (see Focusing Telescope section)
Remove plastic insulator from between Red Dot Finderscope battery and battery clip.
Turn Red Dot Finderscope on.
Looking through Red Dot Finderscope, turn adjustment wheels until the red dot is precisely centered on the same object
already centered in Main Telescope Tube’s field of view.
Now, objects located first with the Red Dot Finderscope will be centered in the field of view of the main telescope.
M
FOCUSING TELESCOPE
1. After selecting the desired eyepiece, aim main telescope tube at a land-based target at least 200 yards away
(e.g. a telephone pole or building).
2. Fully extend Focusing Tube by turning Rack and Pinion Focusing Mechanism.
3. While looking through selected eyepiece (in this case the 20 mm), slowly retract Focusing Tube by turning Rack
and Pinion Focusing Mechanism until object comes into focus.
DETAILED ASSEMBLY (CONTINUED)
7.
DETAILED ASSEMBLY
No tools are required for assembly of your telescope.
Remove all components from the carton and identify all components. It is a good idea to lay all the parts out in front of
you before assembly. Since your telescope is a precision optical system the parts require careful handling—particularly the
onboard computer, telescope, eyepieces, and various accessory lenses.
SET UP TRIPOD AND ACCESSORY TRAY
1. Stand Northstar Computerized Star Locator Assembly and attached tripod legs in
the upright position. Spread tripod legs to a comfortable distance.
2. Fold down the accessory tray braces and place the Quick Release Accessory
Tray on top of braces. (See Quick Assembly Diagram)
3. Turn accessory tray until it snaps into place.
4. Adjust tripod leg height to suit by opening tripod leg lever and extending tripod legs
to desired height. Clamp Tripod Leg lever closed when complete.
ATTACH TELESCOPE TUBE
1. Locate Main Telescope Tube.
2. Remove Telescope Tube Thumb Nuts from side of Telescope Tube (78-8831 and 78-8846 only). For 78-8890, back out
silver lug screw on Telescope Mount top.
3. Position Main Telescope Tube Attachment Bolts through Telescope Tube Bracket at the top of the Northstar Computerized
Star Locator Assembly (78-8831 and 78-8846 only). For 78-8890, slide black telescope tube bracket into telescope
mount receiver. Make sure telescope is pointing in the correction direction. (Logo on telescope tube should be right-
side up.)
4. Reattach Telescope Tube Thumb Nuts to Main Telescope Tube Attachment Bolts once Main Telescope Tube and
Northstar Computerized Star Locator Assembly are assembled together (78-8831 and 78-8846 only). For 78-8890,
tighten silver lug screw on Telescope Mount top into desired depression on the black telescope tube bracket.
ATTACH FINAL TELESCOPE ACCESSORIES
1. Locate Red Dot Finderscope.
For Reflector Telescopes: Remove Finderscope attachment nuts from Main Telescope Tube. Place Finderscope
Assembly over Finderscope Attachment Bolts and reattach Finderscope thumb nuts to Finderscope Mount Bolts.
NOTE: The large end of the finderscope should face the open end of telescope tube.
2. Attach Low Power Eyepiece.
For Reflector Telescope Models: Insert lowest power eyepiece in the focusing mechanism by backing out
eyepiece set screw and inserting eyepiece fully.
3. Tighten all set screws to secure accessories.
6.
SELECTING AN EYEPIECE
You should always start viewing with the lowest power eyepiece, which in this case is the 20 mm lens. Note: the base power
of each eyepiece is determined by the focal length of the telescope objective lens. A formula can be used to determine the
power of each eyepiece: telescope OBJECTIVE lens focal length divided by EYEPIECE focal length = MAGNIFICATION (e.g.
Using the 20 mm lens, a sample calculation could look like this: 750 mm / 20 = 38x or 38 power. Telescope models will
vary in focal length.)
Included with this telescope is a Barlow lens. Barlow lenses are used to double or triple the power of your telescope. Place
your Barlow between the focusing tube and the eyepiece. Using the example above, your 3x Barlow lens would give you a
total power of 114x or 114 power. (38 x 3 = 114x or 114 power). The magnification calculation would look like this: 750
mm /20mm = 38 power. 38 power x 3=114 power.
M
ATTACH REMOTE COMPUTER CONTROLLER AND BATTERY
1. Locate Remote Computer Controller and coil cord.
2. Locate Battery Door on Northstar Computerized Star Locator Base.
3. Remove Battery Door and insert one 9V battery.
4. Replace Battery Door.
5. Attach Remote Computer Controller with coil cord to Northstar Computerized Star Locator Base.
NEVER LOOK DIRECTLY AT THE SUN
WITH YOUR TELESCOPE
PERMANENT DAMAGE TO YOUR EYES
MAY OCCUR
❂
78-8890 1LIM.indd 6-7 6/1/04 11:20:07 AM