Binatone 410 User Manual

Spirit 410 corded telephone, Installation, Desk/wall mount installation

Advertising
background image

Spirit 410 Corded Telephone

Unpacking your phone

Important note---back up batteries

The

Spirit 410 requires 2 x 1.5V AAA size Alkaline batteries

installed into the battery compartment before use.
Warning: The caller display will not work without batteries
installed.

In the box you will find:

Base Unit

Handset

Coiled Handset cord

Telephone line cord
for Base unit

User manual

Keep the packing
materials in a safe
place in case you later
need to transport

Keep your sales (till)
receipt, which is your
guarantee.

the unit

1. LCD Screen

3. M1,M2,M3 Memory buttons
4. Scroll Up & Down buttons
5. Delete button
6. Set/Store button
7. Memory button
8. LNR(Last Number Redial) button
9. Speakerphone button
10. Mute button
11.R(Recall) button
12.Pause button

2. Ringer light indication

1

2

3

4
5

6

7

8
9

10

11

12

2. Installation

1.

Locating the Base unit

The Base unit should be placed on a level surface, in a position where:
„

the telephone line cable will reach your telephone line socket or extension socket.

„

it is not close to a sink, bath or shower, or anywhere else where it might get wet.

„

it is not close to other electrical equipment - fridges, washing machines,

2. Plug the coiled handset cord into the Handset.

Plug the other end into the jack on the left

side of the Base unit.

3. Place the Handset in the Base unit.

Make sure the plugs

click into place.

4. Plug the telephone line cord

free end into a modular wall jack.

Press the cable into the groove so

5. Lift the Handset and check

for Dial tone in the earpiece.

Always use the

telephone line

cord supplied

with your

Spirit 410 phone.

Other telephone

line cords may

not work.

to Modular
Wall jack

microwave ovens, TVs, fluorescent lights, etc.

that the Base unit stands level.

„

Installing (or Replacing) the Battery

IMPORTANT

- Before removing the battery compartment cover,always

make sure the base unit is disconnected from the telephone line.

Install 2 pcs of Alkaline AAA batteries into the battery compartment and

place back the cover before use.

Note: 1) Please do NOT use Rechargeable batteries in this phone.

,-8806: 27 458 24.39/0/ 810 9428

2)

?GDL QGD A@QQDOT HP JMS<

CHPNJ@T

QGD A@QQDOHDP< QGDT SHJJ ADBMKD QMQ@JJT CHPBG@OFDC @LC TMRO CHPNJ@T PBODDL SHJJ LMQ SMOI=

will show up of the

SIZE AAA

SIZE AAA

SIZE AAA

SIZE AAA

PBODDL= >ETMR CM LMQ ODNJ@BD

3. Desk/Wall mount installation

To place the

Spirit 410 on a desk, connect

the bottom of the phone in the slots near the rear of the base

as shown below .

Desk Mount

Insert the rigid clips of the stand into the slots

the phone (

near the rear of

the flexible clips clicks into place.
To remove the stand, (1) pinch the flexible clips, (
the stand, and then (3) slide up and forward (3) as shown below.

To place the

Spirit 410 on a wall, connect

bottom of the phone in the

cover as shown

Wall Mount

below.

the stand to

on the bottom of

the base). Press down firmly until

2) pull back

the stand to the

slots

near the front of the base

0

and

inatone

.com/

08453459677

0818762092

3

online

Desk/Wall mounting continue...

Insert the rigid clips of the stand into the slots on the bottom of

near the front of

the flexible clips clicks into place.

To remove the stand, (1) pinch the flexible

the stand, and then (3) slide up and forward as shown below.

Mark two points on the wall that are 92mm apart to lay the

fixing centers as shown below.

the phone (

the base). Press down firmly until

clips, (2) pull back

BE CAREFUL to check that there are no

in the wall.

Fix two screws (supplied with the unit) at the

approximately 7mm
Hang the cradle unit on the screws using the wall mount slots.

You may need to remove the

tighten the

does not wobble

cradle with the parking hook on the cradle arranged to fit in the parking recess

under the earpiece on the Handset.

9

electrical wires hidden

marked locations,

between the wall and the the screw head.

telephone from the wall and

that the cradle is securely fixed and

leaving

screws so

. Place the Handset on the

Set Time/Date

1

In standby mode, press SET/STO button.
Ö The display shows ' SET 1 DATE '.

2

Press SET/STO button to confirm.
Ö The 'year' icon will be blinking.

3

Press UP or DOWN button to set the year.

4. Setting up your phone

Press the SET/STO button to enter the menu

UP

DOWN

„

SET 1 DATE

„

SET 2 LCD

„

SET 3 FLASH

Note: The system will time out if you leave

You will need to set the correct time and date

displayed correctly on the display.
If you subscribe to a Caller Display service, the

will be set automatically on

4

Press SET/STO button to confirm.
Ö The 'month' icon will be blinking.

5

Press UP or DOWN button to set the month.

6

Press SET/STO button to confirm.
Ö

The 'date' icon will be blinking.

7

Press UP or DOWN button to set the date.

8

Press SET/STO button to confirm.
Ö

The 'hour' icon will be blinking.

and then use or buttons to cycle

through the following options:

more than 8 seconds between key presses.

receipt of your first incoming call.

9

Press UP or DOWN button to set the hour.

so they can be

time and date

10

Press SET/STO button to confirm.

Ö

The 'minute' icon will be blinking.

Press SET/STO button to confirm the setting.
Ö

The display shows ' SET 2 LCD ' , you can

11

12

or press DELETE button to return to standby mode.

Press UP or DOWN button to set the minute.

Setting up continue...

continue with

programming,

Set LCD

1

In standby mode, press SET/STO button.
Ö

The display shows ' SET 1 DATE '.

2

Press UP or DOWN button until the display

3

Press SET/STO to confirm.

4

Press UP or DOWN button to select your

5

Press SET/STO button to confirm the setting.
Ö

The display shows ' SET 2 LCD ' , you can

programming, or press DELETE button to return to standby mode.

Contrast

shows 'SET 2 LCD'.

viewing level (1~8). The default setting is 3.

comfortable display

continue with

Advertising