Warning, Cleaning and care, Operating instructions – Blue Rhino GWU512B User Manual

Page 8: When heater is on, Re-lighting, Shut down, Caution, Notices, Checking for leaks, Before lighting

Advertising
background image

®

Outdoor Patio Heater Model No. GWU512B

Contact 1.800.762.1142 for assistance. Do not return to place of purchase.

WARNING

FOR YOUR SAFETY:

Be careful when attempting to manually ignite this heater. Holding in

the control know for more than 10 seconds before igniting the gas will

cause a ball of flame upon ignition.

Have a question or are having problems visit www.bluerhino.com or call 1.800.762.1142.

Note: the burner may be noisy when initially turned on. To eliminate excessive noise from
the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat
desired.

When heater is ON:

Emitter screen will become bright red due to intense
heat. The color is more visible at night.

Burner will display tongues of blue and yellow flame.
These flames should not be yellow or produce thick
black smoke, indicating an obstruction of airflow
through the burners. The flame should be blue with
straight yellow tops.

If excessive yellow flame is detected, turn off heater and
visit www.bluerhino.com or call 1.800.762.1142.

Re-lighting

Note: For your safety, control knob cannot be turned “OFF” without first depressing control
knob in PILOT position and then rotating it to “OFF”.

1. Turn control knob to “OFF”.

2. Wait at least 5 minutes, to let gas dissipate, before attempting to relight pilot.

3. Repeat the “Lighting” steps.

Shut Down

1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound

when extinguished.) Burner will extinguish but pilot will remain “ON”.

2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”.

3. Turn tank valve clockwise to “OFF” and disconnect regulator when heater is not in use.

Note: After use, some discoloration of the emitter screen is normal.

Cleaning and Care

Caution

1. All cleaning and maintenance should be done when patio heater is

cool and with the fuel supply disconnected.

2. DO NOT clean any patio heater part in a self cleaning oven. The

extreme heat will damage the finish.

Notices

1. Abrasive cleaners will damage this product.

2. Never use oven cleaner to clean any part of heater.

3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage

the finish.

4. More frequent cleaning may be required as necessary. It is imperative that control

compartment, burners and circulating air passageways of the heater be kept clean.

5. Spiders and insects can create a dangerous condition that may damage heater or

make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away
smaller particles.

6. Inspect heater before each use.

7. Have heater inspected annually and repairs should be made by a qualified service

person.

8. Check heater immediately if any of the following conditions exist:

a. The smell of gas in conjunction with extreme yellow tipping of burner flames.

b. Heater does not reach proper temperature.

Note: At temperatures less than 40ºF, heat output will be reduced.

c. Heater’s glow is excessively uneven

d. Burner makes popping noises during use.

Note: A slight pop is normal when burner is extinguished.

Operating Instructions

Checking for Leaks

Burner Connections

Make sure the regulator valve and hose connections are securely fastened to the burner and
the tank.

If your unit was assembled for you, visually check the connection between the burner pipe and
orifice. Make sure the burner pipe fits over the orifice.

WARNING

FOR YOUR SAFETY:

Failure to inspect this connection or follow these instructions could

cause a fire or an explosion which can cause death, serious bodily

injury, or damage to property.

If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for
assistance.

Tank/Gas Line Connection

Make 2-3 oz.a of leak solution by mixing one part liquid
dishwashing soap with three parts water.

Make sure control knobs are “OFF”.

Turn LP gas tank “ON” at valve.

Spoon leak check solution at all “X” locations

If any bubbles appear turn LP gas tank “OFF”, reconnect
and re-test. If you continue to see bubbles after several
attempts, disconnect LP gas source and contact
1.800.762.1142 for assistance.

If no bubbles appear after one minute turn tank “OFF”,
wipe away solution and proceed.

Before Lighting

Heater should be thoroughly inspected before each use,
and by a qualified service person at least annually.

If relighting a hot heater, always wait at least 5 minutes.

Inspect the hose assembly for evidence of excessive
abrasion, cuts, or wear. Suspected areas should be leak
tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose
assembly specified by manufacturer.

Lighting

Note: this heater is equipped with a pilot light that allows for safer startups and shutdowns.
Pilot must be lit before main burner can be
started.

1. Turn tank valve “OFF”.

2. Push control knob in and turn to “OFF”.

3. Wait 5 minutes for any gas to clear.

4. Turn tank valve “ON”.

5. Open viewing hole by sliding cover to

either side.

6. Push control knob in and rotate to pilot

position.

Note: for initial start or after any tank
change, hold control knob in for 2 minutes to
purge air from gas lines before proceeding.

7. Push igniter button once. Pilot light flame

will appear and be visible through viewing
hole.

8. Release control knob after 30 seconds.

Pilot light will remain lit. If not, return to
step 1.

9. Turn control knob to “HIGH”. Main burner

will light immediately. Flame is visible
through viewing hole. If not, return to
step 1.

10. If for some reason your ignitor fails

to deliver a spark, your heater can be
started by inserting a lit match through
the pilot view hole while pushing the
control knob in while in the pilot position.

LP Gas Line

X

LP Gas Tank Valve

X

X

X

X

X

View Hole

OFF

OFF

LOW

LOW

Pilot

Pilot

(Push in)

HIGH

HIGH

Pilot

Pilot

(Push in)

HIGH

HIGH

LOW

LOW

OFF

OFF

Control Knob

Proper flame height.

Advertising