MTD 3AA - Manual (Page 9)

9
Before Starting Engine
Engine Oil
The engine is shipped with oil in it. Check the oil level
before first use.
1. Stop engine and wait several minutes before checking
oil level. Remove oil fill cap and dipstick.
2. Wipe dipstick clean, insert it into oil fill hole and
tighten securely.
3. With engine on level ground, oil must be to FULL mark
on dipstick. See Figure 8. If oil level is low, add oil.
Adding Engine Oil
Be sure to use the grade of engine oil specified in engine
manual. To add oil:
1. Remove the dipstick from the oil fill. Pour fresh oil
slowly through the plug. Replace dipstick.
2. Check and make sure that the level of oil is up to the
FULL mark on the dipstick.
IMPORTANT: For complete detailed engine information, see
the separate engine owner’s manual included with this unit.
Gasoline
WARNING: Gasoline is flammable and
caution must be used when handling or
storing it. Do not fill fuel tank while the
snow thrower is running, when it is hot
or when it is in an enclosed area.
WARNING: Keep your snow thrower away
from any open flame or an electrical spark
and do not smoke during fueling.
3. Never fill the fuel tank completely. Fill the tank to
no more than 1/2 inch below bottom of filler neck to
provide space for expansion of fuel.
NOTE: This unit may include a fuel plug, which is only
used during assembly to keep dirt and debris out of fuel
tank. Discard the fuel plug before filling the fuel tank.
5. Always use clean, fresh, unleaded grade automotive
gasoline. Fill the fuel tank outdoors and use a funnel
or spout to prevent spilling. Make sure that the
container from which you pour the gasoline is clean
5
Operation
Gasoline is flammable
and caution must be
used when handling
or storing it. Do not
fill fuel tank while
the snow thrower is
running, when it is
hot or when it is in an
enclosed area.
Keep your snow
thrower away from
any open flame or an
electrical spark and
do not smoke during
fueling.
Be sure no one other
than the operator is
standing near the
snow thrower while
starting or operating.
Do not operate this
snow thrower unless
the chute assembly
has been properly
installed and is
secured.
The electric starter
must be properly
grounded at all
times to avoid the
possibility of electric
shock to the operator.
If your house wiring
system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
WARNING
and free from rust or other foreign particles. Make
sure to wipe off any spilled fuel before starting the
engine.
6. At the end of the job, empty the fuel tank if the snow
thrower is not going to be used for 30 days or longer.
Store gasoline in a clean container and keep the cap
in place on the container.
CAUTION: Never use engine or carburetor cleaner
products in the fuel tank.
To Start Engine
WARNING: Be sure no one other than
the operator is standing near the snow
thrower while starting or operating. Do
not operate this snow thrower unless
the chute assembly has been properly
installed and is secured.
For location of all the engine controls referred to in this
section, see the engine owner’s manual.
Recoil Starter - Cold Start
1. Make sure that auger and drive controls are
released. Attach spark plug wire to spark plug.
2. Turn fuel valve on, if so equipped.
3. Move throttle control to FAST position.
4. Push key into the ignition slot so that it snaps into
place. Do not turn key.
5. Rotate choke control to FULL choke position.
6. Push primer button while covering the vent hole.
Remove your finger from the primer between primes.
Do not prime if temperature is above 50º F; prime
two times between 50º F and 15º F; and prime four
times below 15º F.
7. Grasp starter handle and pull rope out slowly until engine
reaches start of compression cycle (rope will pull
slightly harder at this point). Let the rope rewind slowly.
8. Pull rope with a rapid, continuous, full arm stroke.
Keeping a firm grip on the starter handle, let the rope
return to the starter slowly. Repeat until engine starts.
9. As the engine warms up, rotate the choke knob slowly
to OFF position. If the engine falters, return to FULL
choke, then slowly move to OFF choke position.
10. Allow the engine to warm up for a few minutes
because the engine will not develop full power until it
reaches operating temperature.
11. Operate the engine at full throttle (FAST) when
throwing snow.
Warm Start:
1. If restarting an engine after a temporary shut- down,
rotate choke to OFF instead of FULL and do not
prime. Pull starter handle as instructed before.
FULL
ADD
Maintain Oil Level
Between FULL and ADD
Figure 8