B&K 200.2 S2 - Manual (Page 6)

BACK PANEL
FUSE FUSEFU
SE
FU
SEF US
E
FUS
E
FUSE FUSEFU
SE
FU
SEF US
E
FUS
E F U S E
C AU T I O N : F O R C O N T I N U E D
P R O T E C T I O N A G A I N S T R I S K
O F F I R E R E P L A C E O N LY W I T H
S A M E T Y P E A N D R AT I N G .
C H A N N E L 2 O U T P U T C H A N N E L 1 O U T P U T
C H A N N E L 1 I N P U T C H A N N E L 2 I N P U T
C T R L
O U T
1 2 V D C
2 0 0 m A
CONTROL
IN
ALL
OWS
AMPLIFIER
OPERA
TION
WHEN
A
5-24V
SIGNAL
IS
APPLIED
W
ITH
A
3.5mm
MINI
JACK
X L R ( B A L A N C E D )
R C A ( U N B A L A N C E D )
X L R ( B A L A N C E D )
R C A ( U N B A L A N C E D )
R C A I N P U T X L R I N P U T R C A I N P U T
B K
&
S B
IMPLY ETTER! S E R I A L #
C T R L
I N
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N A C L I N E
P O S I T I V E N E G AT I V E P O S I T I V E N E G AT I V E
C O N T R O L I / O
www.bkcomp.com
H i g h Pe r f o r m a n c e
A u d i o / V i d e o S y s t e m s
H a n d - M a d e i n t h e U . S . A .
+12V
L O W
P OWER
RING TIP
GROUND
SLEEVE
+12V
CTRL
ENABLE
X L R I N P U T
1 2 3 4
5 6 7 8
1. AC Fuse Holder - Holds the AC line fuse. This fuse is a 12 amp / 250 volt slow bow fuse. Replace only
with the same type and value fuse.
2. AC Input Receptacle - For attaching the supplied AC power cord to the amplifier.
3. Speaker Outputs - For connecting the speakers to the amplifier. Explained further on page 6.
4. Speaker Fuses - For protection against amplifier damage in the case of shorted speaker wires. Replace
fuse with the same type and value 6 amp slow blow.
5. Balanced (XLR) Input - For connecting signal patch cables (interconnects) from the preamplifier to the
amplifier. Explained further on page 5 and 6.
6. Balanced/Unbalanced Input Select - This switch is used to configure a SINGLE AMPLIFIER CHANNEL
for use as either balanced (XLR) or unbalanced (RCA) line inputs. This switch controls the amplifier channel
and allows signal patch cables (interconnects) to be sourced from either balanced or unbalanced, preamplifi-
er/processor or line outputs. Explained further on page 5 and 6.
7. Unbalanced (RCA) Input - For connecting signal patch cables (interconnects) from the preamplifier to the
amplifier. Explained further on page 5 and 6.
8. Amplifier Control Input/Output - Provides remote switching of the amplifier's standby on/off feature.
Explained further on page 8.
4