Bazooka Phat Tuesday MGA11500H - Manual (Page 15)

+12V GND TURN-ON 1
MIN FUSE 30A X 4 CHIL
BASS BOOST
0
15 dB
30
250
+ - - L R
SPEAKER
LEVEL IN
GAIN
L
R
INPUT
XOVER
FREQ Hz
MIN
MAX
REMOTE
+
30
125
BASS
BOOST
SLAVE IN
10
80
SUBSONIC
FREQ Hz
SLAVE OUT
SOURCE
SLAVE
NORMAL
PHASE
IN OUT
.4V - 12.2V FREQ Hz
PWR \
PROT
+12V GND TURN-ON 1 MIN FUSE 30A X 4 CHIL
BASS BOOST
0
15 dB
30
250
+ - - L R
SPEAKER
LEVEL IN
GAIN
L
R
INPUT
XOVER FREQ Hz
MIN
MAX
REMOTE
+
30
125
BASS BOOST
SLAVE IN
10
80
SUBSONIC FREQ Hz
SLAVE OUT
SOURCE
SLAVE NORMAL
PHASE
IN OUT
.4V - 12.2V FREQ Hz
PWR \
PROT
+12V GND TURN-ON 1 MIN FUSE 30A X 4 CHIL
BASS BOOST
0
15 dB
30
250
+ - - L R
SPEAKER
LEVEL IN
GAIN
L
R
INPUT
XOVER
FREQ Hz
MIN
MAX
REMOTE
+
30
125
BASS BOOST
SLAVE IN
10
80
SUBSONIC
FREQ Hz
SLAVE OUT
SOURCE
SLAVE
NORMAL
PHASE
IN OUT
.4V - 12.2V FREQ Hz
PWR \
PROT
++
CAUTION!
In bridged operation, the amplifiers must see a 2 Ohm load or higher for the
subwoofer(s). Any lower than the above mentioned impedance will cause the amplifiers to
overheat and possibly cause permanent damage to the amplifiers.
+12V GND TURN-ON 1
MIN FUSE 30A X 4
CHIL +12V GND TURN-ON 1
MIN FUSE 30A X 4
CHIL
+ +
+12V GND TURN-ON 1 MIN FUSE 30A X 4 CHIL
BASS BOOST
0
15 dB
30
250
+ - - L R
SPEAKER
LEVEL IN
GAIN
L
R
INPUT
XOVER FREQ Hz
MIN
MAX
REMOTE
+
30
125
BASS BOOST
SLAVE IN
10
80
SUBSONIC FREQ Hz
SLAVE OUT
SOURCE
SLAVE NORMAL
PHASE
IN OUT
.4V - 12.2V FREQ Hz
PWR \
PROT
MASTER
AMPLIFIER
SLAVE
AMPLIFIER
++
When running multiple sets of bridged amplifier’s in large systems all amplifiers can be
linked together so the primary master amplifier can control all amplifiers in the set. In the
following example we show two sets of bridged amplifiers controlled by one master
ampilifer.
Master amplifier’s crossover, bass boost
and subsonic adjustments control
both the master and slave amplifiers.
*4 Ohm
2 Ohm Minimum
*4 Ohm
2 Ohm Minimum
Connect (-) Speaker Terminals Together with 10 Guage Wire Minimum
MASTER AMPLIFIER
1.) Set Phase to IN
2.) Set Source to NORMAL
LL R R
*4 Ohm
2 Ohm Minimum
*4 Ohm load recommended for best efficiency
and to optimize the power output.
EN
GL
IS
H
14 MGA AMPLIFIERS
SLAVE AMPLIFIER
1.) Set Phase to OUT
2.) Set Source to SLAVE
SLAVE AMPLIFIER
1.) Set Phase to OUT
2.) Set Source to SLAVE
SLAVE AMPLIFIER
1.) Set Phase to IN
2.) Set Source to SLAVE