Philips Norelco Kid's Clipper Kid-friendly hair clipper CC5059 Ultra-quiet skin friendly 15 length settings 45mins cordless use-8h charge Contour-following comb - Manual

Contouring without a comb attachment
Remove the hair comb if you are:
w Defining hair lines
w Trimming nape of neck
w Removing single, unwanted hairs
Be careful when you are clipping without comb
attachment as when the Clipper is turned on it
will remove every hair it touches.
1 Be certain Clipper is in the OFF position.
2 Remove the hair comb attachment by
pressing the Hair Length Selector (1) and
sliding the comb off the Clipper (2) (fig. 8).
Never pull off a comb by grasping the flexible top
portion. Always pull off by the bottom part of
attachment.
3 To contour the hairline around the ears,
comb the hair ends over the ears.
4 Tilt the Clipper in such a way that only
one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears.
Only cut the hair ends. The hairline should be
close to the ear.
5 To contour the nape of the neck or
sideburns, turn the Clipper and hold it with
the cutter blades pointing downwards.
6 Move the Clipper slowly and smoothly
following the natural hairline.
Cleaning
w Clean the Clipper and combs after each use.
w Always switch Clipper OFF, unplug and remove
power supply cord from the Clipper before
cleaning.
w Do not use compressed air, abrasive cleaning
agents, scourers or liquids such as alcohol,
benzene, bleach or acetone to clean the
Clipper and attachments.
w Never clean, replace or remove Clipper
attachments with motor ON.
w Never rinse or immerse the Clipper handle in
water or any other liquid.
w Do not apply pressure to cutters.
w Do not touch cutters with hard objects as this
may damage them.
w Use a soft, dry cloth to clean the Clipper
handle.
During Use:
w If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or using
cleaning brush provided. Remember to adjust
the clipping length back to your selected setting
where you replace the comb on the Clipper.
After Each Use:
1 Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
2 Remove the hair comb attachment by
pressing the Hair Length Selector (1) and
sliding the comb off the Clipper (2) (fig. 8).
3 Push the center top end of the cutter
blade upwards with your thumb until it
opens (fig. 9).
4 Clean the cutting unit with the cleaning brush
supplied (fig. 10).
5 Clean the inside of the Clipper with the
brush supplied (fig. 11).
6 Clean the handle, combs and the adaptor
with the cleaning brush supplied or with
a dry cloth.
7 Close the cutting unit until it ‘clicks’ into
place.
Replacing The Cutting Unit
If your cutters become damaged or worn, do
not continue using the Clipper. Replace cutters
immediately.
1 Open the cutting unit (fig. 9).
2 Remove the old cutting unit by pulling it
upwards and then pull off the Clipper.
3 Place the notch of the new cutting unit into
the slot.
4 Push the cutting unit back onto the Clipper
until you hear a ‘click’.
This Clipper has no other user-serviceable parts.
For assistance call 1-800-243-3050.
ENGLISH
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electrical appliance, basic
safety precautions should always be followed,
including the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a clipper that has fallen
into water. Unplug immediately.
2. This appliance is NOT a toy. The appliance
is an electric hair clipper. Keep the
appliance out of reach of young children.
3. Use clipper only in a dry condition. Do not
use while bathing or in a shower.
4. Do not place or store clipper where it can
fall or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.
5. Always unplug this clipper from the
electrical outlet immediately after using,
except when clipper is (re)charging.
6. Unplug clipper and remove power supply
cord from clipper before cleaning.
7. The batteries used in this device may
present a fire or chemical burn hazard if
mistreated. Do not disassemble, heat above
100°C (212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when
this appliance and accessories is used by, on,
or near children or invalids.
2. Use this clipper and accessories for its
intended household use as described in
this manual. Do not use attachments not
recommended by Philips Electronics North
America Corporation.
3. Never operate this clipper if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged,
or dropped into water. For assistance call
1-800-243-3050.
4. Do not rinse or immerse the clipper
handle in water or any other liquid.
5. Keep the clipper, cord and any attachments
away from heated surfaces.
6. Never drop or insert any object into any
opening.
7. Do not operate, charge, clean or plug in
clipper outdoors or where aerosol (spray)
products are being used or where oxygen
is being administered.
8. Always check cutters, cutting unit and
combs before using the clipper. Do not use
the clipper if cutters, cutting unit or combs
are damaged, as injury may occur.
9. Always attach plug to clipper first, then to
outlet. To disconnect, turn clipper OFF, then
remove plug from outlet.
10. To prevent possible damage to the cord, do
not wrap cord around the clipper.
11. Never put clipper in direct sunlight or
store at a temperature above 140°F.
12. This clipper is for use on human hair only.
Do not use this clipper for any other
purpose.
13. Always store your clipper, attachments and
power plug in a moisture-free area. Make
sure the cord is disconnected from the
clipper.
14. Only use the power plug and other
accessories supplied with the appliance.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as
this will cause a hazardous condition.
Registration
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that
Philips Norelco offers, register your
product at www.norelco.com/register
A Large Comb
B Cleaning Brush
C Appliance Plug
D Adaptor
E Small Comb
F Hair Length Selector
G Cutting Unit
H On/Off Button
I Adaptor Cover
J Charging Light
Full Two-Year Warranty
45-Day Money-Back Guarantee
Put It To The Test
Like many new products, your Philips Norelco Kids
Hair Clipper may take a little getting used to. If you
are using an electric Clipper for the first time, or if
you’ve been using a different brand, take the time to
acquaint yourself with your new Hair Clipper.
Your Kids Hair Clipper is quiet and easy to use with
rounded blades and comb tips that help prevent
scratching the skin for a safe and pleasant haircut
every time.
Put your new Hair Clipper to the test. We guarantee
precise, professional results or Philips Norelco will
refund you the full purchase price as long as the
request is received within 45 days of purchase.
To Charge/Recharge
w Fully charge Clipper before using for the first
time, after non-use for a long period of time or
when the green charging light turns orange.
w Charging or recharging at temperatures below
40˚F or higher than 95˚F adversely affects
lifespan of the battery.
w Do not charge Clipper in a pouch.
w Always unplug Clipper from the electrical
outlet immediately after use, except when
Clipper is (re)charging.
1 Be certain Clipper is OFF.
2 Open the adaptor cover and insert the
adaptor directly into the Clipper (fig. 1)
and plug the appliance plug into any 120V AC
outlet. Use only the cord provided.
w An adaptor plug may be necessary for
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for power outlet.
3 After a few moments, the green Charging
Light on the appliance will blink to indicate
the Clipper is charging (fig. 2).
w It will take approximately 8 hours to fully
charge the Clipper for a cordless clipping
time of up to 45 minutes.
4 After the Clipper is fully charged, the green
Charging Light goes off.
5 Disconnect the cord and unplug from
electrical outlet.
Corded Hair Clipping
1 Open the adaptor cover and insert the
adaptor provided to Clipper and plug
Clipper into electrical outlet (fig. 1).
2 Turn Clipper ON by pressing the ON/OFF
Button once (fig. 3) and begin clipping.
3 Turn Clipper OFF and unplug.
Cordless Hair Clipping
1 Charge according to directions. Unplug
Clipper from outlet and remove cord.
2 Turn Clipper ON by pressing the ON/OFF
Button once (fig. 3) and begin clipping.
3 If the charge runs low while clipping, the
green Charging Light will turn orange.
The Clipper still contains enough power for
approximately 15 minutes of cordless clipping.
4 If the motor starts to run slowly, simply
connect cord provided to Clipper and outlet
to continue clipping.
Hair Clipping
w Use this Clipper for its intended household
use as described in this manual.
w Make sure that the appliance is fully charged
before you start clipping hair.
w Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
w Only use the appliance on clean, dry hair.
w Do not use on wet hair.
w Before you begin, comb the hair in the direction
of growth (fig. 4).
w To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Storage
w Be sure the Clipper is turned OFF. Remove
cord from outlet and Clipper before storing
in a safe, dry location where it will not be
crushed, banged, or subject to damage.
w Do not wrap cord around the Clipper when
storing.
w Store cord in a safe location where it will not
be cut or damaged.
w Do not place or store the Clipper where
it can fall or be pulled into a tub or sink, water
or other liquid while plugged in.
Assistance
For assistance, call toll free:
1-800-243-3050
or visit our website:
www.philips.com/norelco
Information is available 24 hours a day,
7 days a week.
Battery Removal
w This Philips Norelco Clipper contains a
rechargeable Lithium-Ion battery which must
be disposed of properly (Fig. 12).
w Battery may only be removed when the Clipper
is to be discarded.
w For assistance, visit our website,
www.philips.com/support or
call toll free: 1-800-243-3050
1 Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
2 Allow Clipper to run until the battery is
empty/depleted.
3 Turn Clipper OFF.
4 Remove any comb attachment.
5 Push the middle part of the cutting unit
upwards with your thumb until it opens
(Fig. 13).
6 Undo the two screws in the hair chamber
(Fig. 14).
7 Use both hands to separate the front part of
the housing from the back part and remove
the front part of the housing (Fig. 15).
8 Undo the 4 screws next to the battery
(Fig. 16).
9 Remove the bumper (Fig. 17).
10 Undo the 2 screws of the socket at the
bottom of the appliance (Fig. 18).
11 Remove the socket from the appliance
(Fig. 19).
12 Lift the rechargeable battery and the printed
circuit board out of the appliance and cut the
connecting wires (Fig. 20).
13 Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
14 Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
15 Contact your local town or city officials
for battery disposal information or call
1-800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Clipping with small or large comb
1 Be certain Clipper is OFF.
2 Select the comb attachment. The remaining
hair length after clipping is indicated on the
sides of each comb (fig. 5).
– Small comb: 1/8 – 7/8 in. (3-21mm)
– Large comb: 1 – 1 3/4 in. (24-42mm)
3 Slide the selected comb into the guiding
grooves on both sides of Clipper and push
until you hear it ‘click’ into place (fig. 6).
Make sure the comb attachment locks properly
into position.
4 Press the Hair Length Selector (1) and slide it
to the desired setting (2) (fig. 7).
5 The setting indications on the sides of the
comb show the selected setting.
When you are clipping for the first time, start at
the maximum clipping length setting (7/8 in./21mm
or 1 3/4 in./42mm) of the small or large comb to
familiarize yourself with the appliance and prevent
accidentally trimming hairs too short. As you
become familiar with the settings, adjust the Hair
Length Selector to desired trimming length.
6 Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result.
7 Since all hairs do not grow in the same
direction, move the appliance slowly over the
crown from different directions (i.e. upwards,
downwards and across) to achieve an even
result.
8 Always move the appliance against the
direction of hair growth.
9 Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
10 For best results with curly, sparse or long
hair, use a styling comb to guide the hair
towards the Clipper.
11 Turn the Clipper off regularly during clipping
and remove the hair comb to blow and/or
shake out hair that has accumulated.
w REMEMBER: You must reset the hair length
selector back to your desired setting every
time you replace the hair clipping comb on the
appliance.
TIP: Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
The Fade
w This cut allows you to achieve a smooth
transition from longer hair on top of the
head to shorter hair on the back and sides
of the head.
1 Slide the large comb into the guiding grooves
on both sides of the Clipper and push until
you hear it ‘click’ into place (fig. 6).
2 Press the Hair Length Selector (1) and slide
it to the maximum setting (2) of 1 3/4 in./
42 mm (fig. 7).
3 Clip the desired areas of the head.
4 Then choose a shorter setting and cut all
parts of the head except the top where you
want the hair to be longer.
5 Repeat until all hairs have the desired length.
Cutting over a Styling Comb or Fingers
w This technique can be used to obtain hair
lengths over 1 3/4 in./42 mm.
1 Remove the hair comb attachment by
pressing the Hair Length Selector (1) and
sliding the comb off the Clipper (2) (fig. 8).
Never pull off a comb by grasping the flexible top
portion. Always pull off by the bottom part of
attachment.
2 Comb a small section of hair upwards.
3 Lift the hair with a styling comb and hold it
between your fingers.
The amount of hair you wish to cut should extend
beyond your fingers.
4 Cut the hair extending from the fingers
or comb.
5 Continue this procedure, working from the
front to the back of the head.
6 Comb hair often to remove trimmed hair
and to check for uneven areas.
1 2 3
4 5 6
7 8 9
10 11 12
13 14 15
16 17 18
19
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper send the product back and we’ll refund you the
full purchase price.
The Clipper must be shipped prepaid by insured
mail, insurance prepaid, have the original sales
receipt, indicating purchase price and date of
purchase, and the money-back guarantee return
authorization form enclosed. We cannot be
responsible for lost mail.
The Clipper must be postmarked no later than
45 days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6–8 weeks AFTER
receipt of returned product.
Full Two-Year Warranty
Philips Electronics North America Corporation warrants each new Philips
Norelco product, Model CC5059 (except cutters and combs) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective product
without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not covered by
this warranty. NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal rights, and you may also have other rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Division of Philips Electronics North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS is a Registered Trademark of Koninklijke Philips N.V.
© 2013 Philips Electronics North America Corporation. All Rights Reserved.
ENGLISH
20
Register your product and get support at
www.norelco.com/register
Always here to help you
Question? Contact Philips
Norelco
Question?
Contact Philips
Norelco
A
B
C
G
F
E
I
H
J D
Features
4222 002 8401 1
CC5059
Rechargeable
Cordless/Cord
Kids
Hair Clipper