Philips 55PW9383 - Manual (Page 34)

A
DJUSTING THE
M
ANUAL
C
ONVERGE
C
ONTROLS
: M
ULTIPOINT
R
ED
/B
LUE
Using the On-screen Submenus: Picture
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
É
▲▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
to Navigate Exit to Adjust
PIP
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/
EXIT
POSITION
VCR ACC
MENU/
SELECT
VOL CH
TV/VCR
ACTIVE
CONTROL
1,5
3,4
to Navigate Exit to Adjust to Adjust Exit to Navigate
to Navigate Exit to Adjust to Adjust Exit to Navigate
to Adjust Exit to Navigate
É
▲▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
PICTURE
MANUAL CONVERGE
SAVE MULTIPOINT
▲
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT STORED
PICTURE
MANUAL CONVERGE
OR
▲
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
PICTURE
MANUAL CONVERGE
UNDO MULTIPOINT
▲
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT RESTORED
PICTURE
MANUAL CONVERGE
OR
RESTORE FACTORY
▲
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
RESTORE FACTORY RESTORED
PICTURE
MANUAL CONVERGE
▲
MULTIPOINT RED
MULTIPOINT BLUE
SAVE MULTIPOINT
UNDO MULTIPOINT
RESTORE FACTORY
PICTURE
MANUAL CONVERGE
6
2
T he Multipoint Red/Blue Convergence controls
allow you to adjust picture convergence at
specific points on the TV screen.
1 Press the MENU/SELECT button to
show the on-screen menu. Press the
CURSOR RING RIGHT to enter the
PICTURE menu, then the CURSOR
RING DOWN repeatedly until
MANUAL CONVERGE is highlighted.
2 Press the CURSOR RING RIGHT to
enter the MANUAL CONVERGE sub-
menu. Press the CURSOR RING DOWN
repeatedly until MULTIPOINT RED or
MULTIPOINT BLUE is highlighted. Then
press the CURSOR RING LEFT or
RIGHT to enter Navigate mode.
3 Press the CURSOR RING LEFT,
RIGHT, UP, or DOWN
to move to a
cross hair that has a color outline. Then
press the STATUS/EXIT button to enter
adjust mode.
4 Press the CURSOR RING LEFT,
RIGHT, UP, or DOWN
to adjust the
cross hair until the color outline is
gone.Then press the STATUS/EXIT
button to return to NAVIGATE mode.
Repeat steps 3 and 4 until all misaligned
cross hairs have been adjusted.
5 For your adjustments to be stored in the
TV’s memory, you must activate SAVE
MULTIPOINT.
NOTE:
If you are not satisfied with the
adjustments you just made and want to
start over, you can use the UNDO
MULTIPOINT control. This control
allows you to undo the adjustments, but
only if you use it before saving.
To save your multipoint adjustments,
press the MENU/SELECT button
to
return to the MANUAL CONVERGE
menu. Press the CURSOR RING DOWN
repeatedly until SAVE MULTIPOINT is
highlighted. Then press the CURSOR
RING LEFT or RIGHT to store your
adjustments in the TV’s memory.
Or, to undo the multipoint adjustments
you just made,
highlight UNDO
MULTIPOINT and press the CURSOR
RING LEFT or RIGHT.
Or, to restore the TV’s convergence to
factory settings,
highlight RESTORE
FACTORY and press the CURSOR RING
LEFT or RIGHT.
6 Press the STATUS/EXIT button to
exit the menu.
H
ELPFUL
H
INTS
• The on-screen display
will disappear after 20
seconds of inactivity. If
this happens, simply
press the
MENU/SELECT
button to bring the
MANUAL
CONVERGE
submenu back.
• If you should experi-
ence a power outage
before saving your
multipoint-convergence
settings, your settings
will be lost.
34