Cable tv, Cable box with rf in/out, Cable box with a/v outputs – Philips 19PFL5622D-37 User Manual
Page 13
6
- Cable TV
Connect the cable TV signal to the
CABLE/
ANTENNA 75 jack at the bottom of the TV.
See page 13 for details on using Autoprogram to store
channels in the TV’s memory.
Note: This connection will supply stereo sound to the TV if
the station you are viewing broadcasts stereo sound.
- Cable box with RF IN/OUT
• Connect the incoming cable TV signal to the cable
IN
jack on the back of the cable box.
• Connect a coaxial cable (not supplied) from the
TO TV
jack on the back of the cable box to the
CABLE/
ANTENNA 75 jack at the bottom of the TV.
Note: Your cable box may have a different label for the
TO
TV
jack. Commonly used labels include
OUTPUT
or
OUT
.
• Set the
OUTPUT CH switch on the cable box to CH
3 or 4 (whichever is correct for your cable box). Next,
tune the TV to the corresponding channel. Once
tuned, change channels using the cable box, not the TV.
Note: This connection will not supply stereo sound to the TV. The
reason is that the RF output on a cable box - labeled
TO TV
,
OUT
or
OUTPUT
for example - will not send a stereo signal to
the tuner (VHF/UHF) input on a TV.
- Cable box with A/V outputs
• Connect the incoming cable TV signal to a signal
splitter (not supplied). The signal splitter enables you to avoid
having to use the TO TV jack on the back of the cable box.
This jack will not supply stereo sound to the TV.
Note: Your cable box may have a different label for the
TO
TV
jack. Commonly used labels include
OUTPUT
or
OUT
.
• Connect a coaxial cable (not supplied) to a connector on
the signal splitter and to the
CABLE/ANTENNA 75
jack on the TV.
• Connect another coaxial cable (not supplied) to a
connector on the signal splitter and to the cable
IN jack
on the back of the cable box.
• Connect A/V cables (not supplied) to the
VIDEO IN and
AUDIO L and R outputs on the back of the cable box
and to the
AV2 or Side AV video (labeled VIDEO IN) and
AUDIO (labeled
L and R) jacks on the back of the TV.
• To view programs from your cable box, fi rst press the
SOURCE button on the remote control.
• Press the cursor down or up buttons until the
AV2 or Side
AV signal source is selected.
• Press the
OK button to confi rm your selection. The AV2 or
Side AV input source becomes current for the viewing of
cable TV programs through your cable box.
Note: If your cable box audio/video outputs do not supply
video and stereo audio to the TV, you will need to make the
connection shown above in “Cable box with
RF IN/OUT
.
CABLE OR ANTENNA
75
CABLE
2
I
M
D
H
1
I
M
D
H
E
C
CABLE OR ANTENNA
75
Cable box
/OUT
OUTPUT
(TO TV)
IN
CABLE
3
2
ANTENNA
ANTENNA
Watching cable TV programs that don’t
require the use of a cable box.
Since you’ve connected the cable TV signal
directly to the TV’s tuner, you can also watch
unscrambled programs by simply tuning to
the desired channel; however, you must fi rst use
Auto program to store available channels in the
TV’s memory. (p. 13)
Note: This connection will supply stereo sound to the
TV if the station you are viewing broadcasts stereo
sound.
Cable box
OUT
IN
75
CABLE OR ANTENNA
SPLITTER
3
2
CABLE
1
4
AV2:
L+R+CVBS
ANTENNA
PC IN
VGA
SIDE AV
VIDEO
IN
S-VIDEO
R
L
VIDEO IN
S-VIDEO
AUDIO R
AUDIO L