Philips 717042848 - Manual (Page 2)

2
SAFETY INSTRUCTIONS - PART B E N G L I S H
• The manufacturer advises the correct use of Luminaires (lightin xtures)! Therefore always follow
these instructions to ensure correct and safe installation and functioning of the luminaire and keep it for
future reference.
• Turn off electrical power at main fuse or circuit breaker box before commencing installation,
maintenance or repair.
• If in doubt, consult a quali ed electrician or contact your retail outlet. Ensure that you always install the
luminiare to the local electrical code. Certain regulations indicate that luminaires should be installed by
a quali ed electrician.
•
• Do not connect this luminaire to a non-grounded electrical system. WARNING: Installing this xture in
a non-grounded electrical system could allow metal parts of the luminaire to carry electrical current if
any wires or wire connections become broken or loose. Under this condition, anyone coming in contact
with the luminaire is subject to electric shock which could cause injury or death.
• Always use wire nuts/connectors rated for the correct gauge and number of wires used. CAUTION: Be
certain that no bare wire strands are exposed outside of the wire nuts/connections (if applicable).
• Be careful not to damage or cut the wire insulation (covering) during installation. Do not permit wires
to contact any sharp edges.
• Do not remove thermal insulation pad(s). Doing so will result in increased temperatures and possible
risk of re.
• Maintain interior lighting with a dry cloth duster, do not use abrasives or solvents. Avoid liquid on all
electrical parts.
• Always consider all the technical speci cations of the luminaire. Verify the stated icons on the
identi cation label on the luminaire and the icons that are shown in part A of your safety instructions.
instructions.
01- This luminaire should only be installed indoors.
02- The luminaire is suitable for outdoor usage.
03- Only suitable for dry locations.
04- Suitable for damp locations.
05- Suitable for wet locations.
06- Luminaire is suitable for base up mounting.
07- Luminaire is suitable for base down mounting.
08- Luminaire is suitable for horizontal mounting.
09-
10-
11-
12- Always observe the minimum distance between the lamp and the surface being lit as indicated on
the icon.
13- Free air space of at least 4 inches must be kept between top of shade and bottom of canopy.
14- Immediately replace a cracked or broken safety glass and use only manufacturer approved parts.
15- Strip the wire as indicated in the diagram.
16- Use heat-resistant cable for wiring the luminaire into the mains.
17-
18- The
19- The .
20- The luminaire is only suitable for a lamp with built-in safety or a low pressure lamp. An extra safety
glass is not necessary.
21- Capsule and linear halogen lamps may not be touched by bare hands.
22- The luminaire is equipped with a fuse. If the luminaire is out of order after the bulb has been replaced,
the internal fuse has to be replaced. If contact with the internal wiring can be made during this opera-
tion, this should be done by a competent electrician.
23-
type (especially important for low voltage luminaires).
24- The Luminaire cannot be used with a dimming circuit.
25- The Luminaire utilizes GU24 Base electrical components and cannot be used with dimmers, timers or
other control devices.
26- Luminaire with time and light setting options. Minimum and maximum will be shown in the icon in
part A.
27- The luminaire can be placed at a maximum of 20ft height.
28- To reach an optimal working, you have to place the luminaire on the height mentioned in the icon. The
maximum and minimum reach of the detector is also mentioned in the icon in part A.
29- The standard active range of vision of the detector covers the given degrees mentioned in the icon.
30- Ensure that you don’t drill through electrical wires or any other obstruction in the wall or ceiling dur-
ing installation!
31- This luminaire contains in some places very hot parts.
32- This product is not suitable for children under 14 years.
The Luminaire – as well as all other products from the collection – is designed and tested in accordance
with the strictest national safety standards. In case of construction faults or material damages, the manufac-
turer gives a guarantee up to 2 year (unless otherwise stated on the packaging). Light bulbs and batteries
do not fall under the guarantee terms. Most ballasts, transformers, electronic drivers and emergency
battery packs are covered by separate ballast manufacturer’s warranties, contact Philips for exceptions. Any
damage caused to the luminaire in extreme conditions (coastal areas, industrial surroundings, farm environ-
ments) will not be covered by the guarantee. The period of guarantee starts from the purchase date and is
only valid on presentation of receipt. The guarantee is void if the luminaire was not installed following the
a result of misuse or wrong application of the luminaire.
Alterations
Observe the correct color of the wiring before installation: white or white tracer (Neutral), black
or black tracer (Line), green or bare copper wire (Ground) and green tracer for bonding purpose.