Philips Hospitality LED-LCD TV 46HFL5784L 117cm-46" class b-LAN™ ProIdiom® MPEG-4 - Manual (Page 10)

10
46 42 39HFL5784D L
Configure standard TV settings
This menu will allow the configuration of the standard TV
parameters.
Options: Language, Picture, Sound, Caption settings, Child
Lock, EasyLink
Use of Slideshow application
The slideshow application will enable a basic signage mode.
1
Insert the USB stick with the graphic files.
2
Press MENU on the setup remote control to display the
setup menu.
3
Select Applications or Slideshow.
4
For testing and fine tuning, select Run from USB. The
TV will start displaying the files, with the parameters
configured in the Slideshow menu.
5
When all is confirmed, select Copy to TV. The graphic
files will be copied to the TV memory.
6
Select Configuration, Switch On and OSD, Switch On
Program or Slideshow in the main setup menu. Next
time the TV will switch On, will automatically start the
slideshow application.
Configure the upgrading and cloning
settings
Preface:
The Upgrades section of the Hospitality TV setup menu has
three possible sources:
1. IP
2. USB
3. RF
Only the USB source is bidirectional, meaning that the TV
can either read from the USB, or write to the USB. The
IP and RF sources are unidirectional – read only. It cannot
write to them.
If the source USB is selected, there are 5 upgrade types
available:
1. All
2. Software (TV fi rmware(s))
3. Assets (Slideshow pictures)
4. Clone (TV settings and channel map)
5. P:I Key (Change TV between PPV ↔ FTG modes)
Of these, only the Assets and Clone types are bidirectional.
The All, Software, and P:I Key types are read only. So, if
either Assets or Clone is selected, an additional menu item:
Direction appears. There are two possible directions:
1. To TV (reads data from the USB, copies it to the TV)
2. From TV (reads data from the TV, copies it to the USB)
How to capture a clonefi le from the TV to a
USB storage device
1.
Insert a USB storage device into the TV USB terminal.
(It must have suffi cient free space to hold a TV clonefi le
– about 5 MB.)
2.
Press MENU on the setup remote control to display the
setup menu.
3.
Scroll down to and select Upgrades.
4.
Select Source and select USB then press OK.
5.
Select Type and select Clone then press OK.
6.
Select Direction and select from TV then press OK.
7.
Select Execute and select Start then press the OK.
8.
After the successful completion, Upgrade Completed!
Press OK to continue message appears on screen.
How to install a clonefi le from a USB storage
device to the TV
1.
Insert the USB storage device containing the clonefi le
into the TV USB terminal.
2.
Press MENU on the setup remote control to display the
setup menu.
3.
Scroll down to and select Upgrades.
4.
Select Source and select USB then press OK.
5.
Select Type and select Clone then press OK.
6.
Select Direction and select To TV then press the OK.
7.
Select Execute and select Start then press the OK.
8.
After the successful completion, Upgrade Completed!
Press OK to continue message appears on screen.
9.
After pressing OK, the TV will restart and initialize with
the new values
Note
• When selecting RF and its respective parameter, ensure that
this is the channel that will be used to stream the data and it is
not used by any video channel.
• RF cloning/upgrading must be used with a Gateway Network
Appliance (GNA) device. For more information on the GNA,
contact your Philips authorized agent or dealer.
LC11_PHILIPS_hospitality_EN_QG.indd 10 LC11_PHILIPS_hospitality_EN_QG.indd 10 2013/07/25 11:02:06 2013/07/25 11:02:06