Philips 46PP9352 - Manual (Page 11)

11
C
ONNECTING A
S
TANDARD
DVD P
LAYER
Rear of TV
ANTENNA IN 75 Ω
INPUT-AV 1 OUTPUT INPUT-AV 2
HD INPUT-AV 4
HD INPUT-AV 5
VIDEO
AUDIO
S-VIDEO
L
R
Y
Pb
Pr
VIDEO
AUDIO
L
R
S-VIDEO
B/Pb
V
H
SYNC
AUDIO
L
R
AUDIO
L
R
R/Pr
G/Y
*(Example: Philips DVD model DVD712)
Rear of DVD Player*
COAXIAL
DIGITAL AUDIO OUT PCM-MPEG2-Dolby Digital-DTS
L R (CVBS)
VIDEO OUT AUDIO OUT S-VIDEO OUT
(Y/C)
SUB WF OUT OPT OUT
1
2
1
2
Y P B /C B P R /C R
VIDEO OUT
2
1
C omponent video inputs allow the highest pos-
sible color and picture resolution in the play-
back of digital signals, such as those of DVD
players. The color difference signals (Pb, Pr) and
the luminance (Y) signal are connected and
received separately. The result is better color
bandwidth information than is possible with com-
posite video (labeled VIDEO on your TV’s jack
panel) or S-Video connections.
To make the connections shown in this example,
you will need:
• three cables for video connections (standard
RCA connectors)
• two cables for audio connections (standard
RCA connectors).
NOTE: The cables are not supplied with your TV.
You should be able to buy them at most stores
that sell electronics. Or you can call our
Customer Care Center at 1-800-531-0039.
1 Connect the YPbPr (component)
VIDEO OUT jacks from the DVD player
to the INPUT-AV 1 YPbPr (component
video) jacks on the rear of the TV.
NOTE: The INPUT-AV 1 YPbPr jacks
will accept 480i (interlaced) output sig-
nals only. The connection example on this
page assumes the use of a DVD player
with interlaced output. Some DVD play-
ers, however, have YPbPr outputs that can
be switched between interlaced and pro-
gressive scan. If you are attempting to use
a DVD player with progressive-scan
(480p output) capability to make the con-
nection shown in this example, you must
be sure to switch the DVD player to inter-
laced. If necessary, refer to the DVD play-
er’s directions-for-use manual for help. If
you want to use the DVD player in pro-
gressive-scan mode, you must use the
HD INPUT-AV 4 jacks (see page 12).
2 Connect the AUDIO OUT L(eft) and
R(ight) jacks from the DVD player to the
INPUT-AV 1 AUDIO jacks on the rear of
the TV.
3 Press the AV button on the remote con-
trol as many times as necessary to select
the CVI (component video input) source
on the TV.
4 Turn the DVD player on and press
PLAY to view the DVD program on
the TV.
Connecting Accessory Devices to Your TV
PIP ON/OFF
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
ACTIVE
CONTROL FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/
EXIT
SURF
ITR/
RECORD
HOME
VIDEO HOME
MOVIES
PERSONAL
SLEEP REC •
PIP POSITION
VCR ACC
MENU/
SELECT
VOL CH
TV/VCR
FORMAT
SAP
PROG.LIST DOLBY V AV
3
CVI
BEGIN
• To simplify making connections, the connec-
tors on audio and video cables are often color
coded. The jacks on your TV are likewise
color coded to match the connectors.
• The names for the component video jacks
may differ depending on the DVD player or
accessory digital source equipment used. For
example, besides YPbPr, you may see
R-Y/B-Y/Y; or CrCbY. Although abbrevia-
tions and terms may vary, the letters B and R
stand for the blue and red color component
signal connectors, respectively, and Y indicates
the luminance signal. If necessary, refer to the
directions-for-use manual for your DVD or
digital accessory for more information.
• You can also connect a satellite receiver to the
TV in a manner similar to the example shown
on this page. If you connect a satellite receiver
to the TV, you will need to use the receiver’s
channel-memorization system to store chan-
nels in the receiver’s memory.
• If you experience difficulties receiving sound
with a DVD disc, check the sound settings
through the DVD disc’s menu.
• The CVI source cannot be displayed in the
PIP window. See page 7 in the Quick Use and
Setup Guide for more on the PIP feature.
H
ELPFUL
H
INTS
To prevent uneven picture-tube aging, do not
leave nonmoving images or picture borders on
the screen for an extended period. See page 60.
W
ARNING