Philips FWC250 - Manual (Page 22)

3139 115 20353 (ENG)
22 TIMER SLEEP TIMER
5 Press CLOCK•TIMER again to
store the setting.
™ The clock starts.
• To exit without storing the setting,
press Çon the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
Timer Setting
• The system can switch on to CD or
TUNER mode automatically at a
preset time. It can serve as an alarm
to wake you up.
• Before setting the timer, make sure
the clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum
level to the most recently
selected volume level.
1 Press and hold CLOCK•TIMER
for more than two seconds to
select timer mode.
™ “12:00 AM ” or “ 00:00" or the
last timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The TIMER starts flashing.
™ The selected source is lit while
other available sources are
flashing.
2 Press CD or TUNER to select the
desired source.
• Before selecting CD, make sure a disc
is loaded in the CD changer tray.
3 Press à or á on the system to set
the hour for the timer to start.
4 Press í or ë on the system to set
the minute for the timer to start.
5 Press CLOCK•TIMER to store
the start time.
™ The timer is now set.
™ The
TIMER remains on the display.
• At the preset time, the timer will be
activated.
™ The selected source will be
played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the
last tuned frequency will be switched
on.
– If the source selected is CD, playback
will begin with the first track of the
selected disc or program. If the CD
trays are empty, the TUNER will be
selected instead.
– The timer will not activate if a recording
is in progress.
To switch off the TIMER
1 Press and hold CLOCK•TIMER
for more than two seconds.
2 Press Ç on the system to cancel the
timer.
™ The timer is now switched off.
™ The display will show "OFF" and
the TIMER disappears.
To start the TIMER again (for the
same preset time and source)
1 Press and hold CLOCK•TIMER
for more than two seconds.
2 Press CLOCK•TIMER again to
store the start time.
™ The timer is now on.
™ The
TIMER appears on the display.
Sleep Timer (only on remote
control)
This feature allows you to select a
length of time after which the system
will switch to the standby mode
automatically.
1 Press SLEEP on the remote control
repeatedly to select a period of time.
™ The selections are as follows (time
in minutes): 15 ™ 30 ™ 45 ™ 60
™ OFF ™ 15 …
™ "SLEEP XX" or "OFF" will be
displayed. " XX" is the time in
minutes.
2 When you reach the desired length
of time, stop pressing the SLEEP
button.
™ The
SLEEP display lights up.
™ The Sleep Timer is now set. Before
the system switches to standby
mode, a countdown of 10
seconds will be displayed.
"
SLEEP 10" ™ "SLEEP 9".... ™
" SLEEP 1" ™ "SLEEP"
While SLEEP mode is activated
• Press
SLEEP once to view the
remaining length of time.
• Press SLEEP twice to change the
pre-selected period of time.
™ The display will show the
remaining time followed by the
sequence of sleep timer options.
To switch off the Sleep Timer
• Press
SLEEP repeatedly until " OFF"
is displayed, or press the
STANDBY-ON button.
pg 01-28/C250/37-En 12/6/00, 2:20 PM 22