Black & Decker Dust Buster CFV9601 - Manual (Page 2)

INSTALLATION INSTRUCTIONS (FIG. 2)
The Floor Vac can be mounted to most walls when using the Wall Mount System included with
this product. Fix the wall mount within reach of an electrical outlet (Figure 2). Mount securely
using appropriate length screws into framing studs or spring type wall anchors into wallboard,
etc. To charge, mount unit into place by pulling out the hidden wall mount hook at the top of
the handle. Next plug power supply plug into nearby 120 volt electrical outlet. Ensure cord is
not too tight so as to pull unit off wall mount. The unit can also be charged when placed in a
convenient position.
RECHARGING (FIG. 3)
From new, the rechargeable cells of the product need a minimum charge time of 16 hours to
ensure full power. We suggest you fully discharge the product when it is used for the first time as
this will help the cells recharge faster. The switch must be in the off (“O”) position, as the product
will not charge if it is in any other position. Plug charging cord into dual-pronged outlet on side
of unit. While charging, the product may get warm, this is perfectly normal and safe. It can
remain on charge indefinitely without damage or danger. It is not possible to “overcharge” the
battery cells with the charger provided.
POWER SWITCH (FIG. 4)
This product is for dry pick-up only.
The vacuum has 3 positions: Hard surfaces, Carpet and Off. From the OFF position, push the
switch forward to first stop (figure 4A) for hard surfaces. Push forward again to end (Figure 4B)
to turn on rotating brush for carpet. To turn the vacuum off, pull the switch all the way back until
you can see the OFF icon “O”.
FLOOR VACUUM (FIG. 5)
To operate as a Floor Vacuum, ensure the DustBuster is in place (figure 5). To turn unit on, refer
to Power Switch section of manual. The full tilt handle lets you vacuum comfortably at any height
and folds down flat to reach under beds and furniture. The vacuum should be stored in the
Floor Vacuum mode.
HAND VACUUM WITH BRUSH (FIG. 6)
This unit operates as a Hand Vacuum with the brush remaining attached for use on carpeted
stairs and other hard to reach areas. When operating in the Floor Vacuum mode, hold onto
DustBuster handle, while sliding upper handle access button up and pulling upwards on the
handle (figure 6). The power switch operates the same as in the Floor Vacuum mode.
DUSTBUSTER (FIG. 7)
This unit operates as a cordless hand held vacuum. When operating in Floor Vac mode or Hand
Vac with Brush mode (Figure 7) press and hold down the DustBuster release button and pull the
unit outward with the handle. The unit will run the same with the power switch in either “ON” or
”Brush” Mode. To replace hand vac, first position nose (opening) over connection to brush head.
Next, snap handle into place until you hear “click” into position.
IMPORTANT: Do not remove DustBuster when unit is hanging from wall mount.
ACCESSORIES (FIG. 8)
Accessories are stored on the product (Figure 8) (excluding CFV1200, CFV9600) and are
fitted into the nose of the DustBuster for use. See Figure 14 for accessory applications.
CLEANING THE PRODUCT (FIGS. 9-13)
WARNING: Never use the Dustbuster without its filters.
NOTE: The filters are re-usable, do not confuse them with disposable dust bags, and do not
throw them away when the product is emptied. We recommend that you replace the
filters every 6-9 months.
FIG. 9
• Remove the dust bowl by pressing the dust bowl release button and pulling the bowl
down and out. To replace the bowl, place it back onto the handle and click firmly into
position.
FIG. 10
• Empty the dust from the bowl and wash if necessary (see Fig. 10).
FIG. 11
• To remove the filter twist it in a clockwise direction. Shake or lightly brush any loose
dust off the filter. This product features Black & Decker’s Double Action Filter System ™ ,
consisting of 2 nested filters. For best results when cleaning make sure filters are separated.
FIG. 12
• Wash the filters regularly using warm, soapy water and ensure that they are completely
dry before using again. The cleaner the filters are, the better the product will perform. It is
very important that the filter is correctly in position before use. The dust bowl can also
be washed in warm soapy water. Ensure that it is dry before re-attaching.
IMPORTANT: Maximum dust collection will only be obtained with clean filters and an empty
dust bowl. If dust begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
FIG. 13
• Never immerse the product in water. A damp cloth and soapy water should be used
to clean the exterior of the motor section. Always ensure the product is completely dry
before re-use or storing.
ECONOMIC USAGE
• Your product is very economical to charge. While it is charging it uses less than half the
amount of electricity used by a common night light.
• When fully charged, the average effective usage times are between 14-16 minutes with brush
on and 16-17 minutes with the brush off.
• It may take several chargings before these times can be achieved.
OTHER INFORMATION
If the product does not work, check the following:
• The charger was correctly plugged in for recharge. (It feels slightly warm to the touch.)
• The charger cord is not damaged and is correctly attached to the base.
• The charger is plugged into a working electrical outlet.
BATTERY REMOVAL AND DISPOSAL
This product uses nickel-cadmium (Ni-Cd) rechargeable and recyclable batteries. When the
batteries no longer hold a charge, they should be removed from the Vac and recycled. They
must not be incinerated or composted.
The batteries can be taken for disposal to a Black & Decker, Company-Owned or Authorized
Service Center. Some local retailers are also participating in a national recycling program (see
“RBRC TM Seal”). Call your local retailer for details. If you bring the batteries to a Black & Decker
Company-Owned or Authorized Service Center, the Center will arrange to recycle old batteries.
Or, contact your local municipality for proper disposal instructions in your city/town.
REMOVAL:
To remove the battery pack for disposal, push the slider (Figure 15) towards the nose of the
Dustbuster. This will release the entire underside of the Dustbuster and will expose the battery
pack for easy removal. Remove the dust bowl, both filters and lift the rubber band off the battery
pack (if fitted) and dislodge the battery pack. Strike the front of the product firmly on a suitable
surface to dislodge the battery pack as shown in Figure 16. It may take a number of strikes
before the battery pack falls out (be careful where it falls). It may be easier to use a screwdriver
or similar object to pry the battery pack from the product. Once removed, the battery pack
cannot be refitted.
MAINTENANCE
Use only mild soap and damp cloth to clean the vac. Never let any liquid get inside the vac;
never immerse any part of the vac into a liquid.
NOTE: Make sure the vacuum is completely dry before using it.
IMPORTANT:
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be performed by authorized service centers or
other qualified service organizations, always using identical replacement parts.
THE RBRC ™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the
battery (or battery pack) at the end of its useful life have already been paid by Black & Decker.
In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid
waste stream and the RBRC program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in
the United States and Canada to facilitate the collection of spent nickel-cadmium batteries. Help
protect our environment and conserve natural resources by returning the spent nickel-cadmium
battery to an authorized Black & Decker service center or to your local retailer for recycling. You
may also contact your local recycling center for information on where to drop off the spent
battery, or call 1-800-8-BATTERY.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow page
directory under “Tools—Electric” or call: 1-800-54-HOW TO (544-6986).
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or
workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it
was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific return policy
regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized
Service Center for repair or replacement at our option. Proof of purchase may be required.
Black & Decker owned and authorized Service Centers are listed under “Tools-Electric” in the
yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state. Should you have any questions, contact
the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
Lorsqu’on utilise un appareil électrique, il faut toujours respecter certaines règles de sécurité
fondamentales, notamment les suivantes.
LIRE ATTENTIVEMENT ET COMPRENDRE TOUTES LES DIRECTIVES AVANT D’UTILISER L’APPAREIL.
AVERTISSEMENT : Le produit renferme des produits chimiques, dont du plomb. Selon
l’état de la Californie, ce produit chimique peut causer le cancer
ainsi que des malformations congénitales, et il présente d’autres
dangers au système reproductif humain. Se laver les mains après
l’utilisation.
AVERTISSEMENT : Afin de minimiser les risques d’incendie, de secousses électriques
ou de blessures.
• Exercer une étroite surveillance lorsqu’on utilise l’appareil près d’un enfant ou que l’appareil
est utilisé par ce dernier. Il ne s’agit pas d’un jouet.
• Afin d’éviter les risques de secousses électriques, ne pas immerger l’appareil ni son chargeur.
• Ne pas se servir d’un aspirateur portatif Dustbuster md pour déchets secs afin d’aspirer des
liquides, des substances toxiques, des liquides inflammables ou combustibles (de l’essence,
par exemple), ni s’en servir dans un endroit renfermant de tels produits.
• Afin de prévenir les risques de trébuchement, ranger l'appareil après chaque utilisation.
• Ne pas se servir d'un aspirateur portatif pour déchets secs ou humides pour aspirer des
substances toxiques, des liquides inflammables ou combustibles (de l’essence, par exemple),
ni s’en servir dans un endroit renfermant de tels produits.
• Ne pas se servir de l’appareil en présence de vapeurs explosives ou inflammables.
• Utiliser l’appareil seulement de la manière décrite dans le présent guide. Utiliser seulement
les accessoires recommandés par le fabricant.
• Ne pas utiliser un appareil dont le cordon ou le chargeur est endommagé, ni un appareil qui
ne fonctionne pas bien, qui est tombé, endommagé, resté à l’extérieur ou a été immergé. Le
confier à un centre de service autorisé.
• Ne pas utiliser ni ranger un aspirateur portatif Dustbuster md pour déchets secs à l’extérieur ni
sur des surfaces mouillées. Ne pas utiliser un aspirateur portatif pour déchets secs ou
humides à l’extérieur.
• Manipuler le cordon avec soin. Ne jamais transporter le chargeur ni le socle par le cordon
ni tirer sur le cordon pour le débrancher. Saisir plutôt la fiche et tirer dessus. Éloigner le
cordon des surfaces chaudes. Ne pas tirer sur le cordon lorsqu’il est autour d’un coin ou
d’un rebord tranchant.
• Ne pas laisser pendre le cordon d’une table ou d’un comptoir, ni le laisser entrer en contact
avec une surface chaude. Placer ou installer l’appareil loin des éviers ou des surfaces chaudes.
• Ne pas nettoyer un appareil électrique branché.
• Ne pas utiliser de cordon de rallonge. Brancher le chargeur directement dans une prise.
• Brancher le chargeur seulement dans une prise standard (120 V, 60 Hz).
• Ne pas utiliser le chargeur avec un autre appareil; ni tenter de charger le produit avec un
autre chargeur. Utiliser seulement le chargeur fourni par le fabricant.
• Éloigner les cheveux, les vêtements amples et les membres du corps des orifices et des pièces
mobiles de l’appareil.
• Ne pas installer d’accessoires lorsque l’appareil fonctionne.
• Ne pas manipuler la fiche ni l’appareil avec les mains mouillées.
• Ne pas insérer d’objets dans les ouvertures de l’appareil. Ne pas utiliser l’appareil
lorsqu’une de ses ouvertures est bloquée. Enlever la poussière, la charpie, les cheveux et
toute autre matière susceptible de réduire le débit d’air.
• Ne pas aspirer des objets pointus qui pourraient endommager l'aspirateur ou le filtre.
• Ne pas faire fonctionner l’appareil sans filtre. Remplacer sans tarder le filtre s’il est endommagé.
• Ne pas se servir de l’appareil pour aspirer des substances en combustion, comme des
mégots allumés, des allumettes ou des cendres chaudes provenant d’un foyer.
• Ne pas utiliser l’appareil sur des surfaces chaudes ni près de celles-ci.
• Faire preuve de prudence lorsqu’on nettoie les escaliers.
• L’appareil est conçu pour une utilisation domestique seulement et non industrielle ou
commerciale.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
IMPORTANTES MISES EN GARDE
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE
LA RAISON PRIÈRE DE COMPOSER 1 800 544-6986
1 . 3 Position Power Switch
2 . Dust Bowl Release Button
3. Dust bowl
4. Upper Handle Release Button
5. Hand Held Vac Release Button
6. Rotating Brush Powerhead
Product Features (Fig. 1)
How To Use
7. Wall Mount Hook
8. Charging Cord outlet
9. Power supply plug
10. Wall Mount
Operation