Philips 60 in Digital Widescreen HDTV Monitor - Manual (Page 5)

5
U
SING THE
I
NSTALLATION
F
EATURES
C
HANNEL
E
DIT
PIP
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/ EXIT
POSITION
VCR ACC
MENU/ SELECT
VOL CH
TV/VCR
ACTIVE
CONTROL
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron AV3
AV4
1
2 SKIPPED
3
1
4
3
2
5
AV3
AV4
1
2
3
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
T his feature allows you to edit or skip channels from the chan-
nel list that have bad or weak signals or channels you do not
want to watch.
1 Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeated-
ly until INSTALL is highlighted. Press the CURSOR
RING right to enter the INSTALL submenu.
2 Press the CURSOR RING DOWN repeatedly until
CHANNEL EDIT is highlighted. Then press the CURSOR
RING RIGHT or LEFT to access the CHANNEL EDIT
list.
3 Press the CURSOR RING UP or DOWN to scroll
through the list of channels. Or press the NUMBER but-
tons on your remote control to select a specific channel.
4 With the channel you want to edit selected, press the
CURSOR RING RIGHT to mark the channel as
SKIPPED. (Channels you mark SKIPPED will not appear
when you use the CH[annel] +/– buttons to change chan-
nels while watching TV.)
When you want to add a channel that has been marked
SKIPPED, press the CURSOR RING UP or DOWN to
highlight the channel. Then press the CURSOR RING
RIGHT to remove the word SKIPPED.
5 Press the STATUS/EXIT button to exit the menu.
Channels that Auto
Program (see above) deter-
mined not to contain active
broadcast signals are
marked SKIPPED.
H ELPFUL H INT
T he AUTO PROGRAM feature will scan for channels with
active broadcast signals and store those channels in the TV’s
memory. It will tune up to 69 channels for antenna, and up to 125
channels for cable. After you run AUTO PROGRAM, you can use
the CH(annel) +/– buttons to quickly and easily select stations.
You can also press the PROG. LIST (Program List) button on
your remote to see a list of the channels.
1 Press the MENU/SELECT button. The on-screen menu
appears. Then press the CURSOR RING DOWN repeated-
ly until INSTALL is highlighted.
2 Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN repeat-
edly until AUTO PROGRAM is highlighted.
3 Press the CURSOR RING RIGHT to begin the automatic
search for channels. The progress of autoprogramming is
displayed.
4 When the programming is done, press the STATUS
EXIT button to exit the menu.
2 1 3
5 4 6
TV
SWAP PIP CH
DN UP
FREEZE
SOUND
MUTE
POWER
PICTURE
STATUS/
EXIT
VCR ACC
MENU/ SELECT
VOL CH
ACTIVE
CONTROL
INSTALL
SEARCH
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
CABLE
PLEASE WAIT
CHANNEL 12
1
4
2,3
After you’ve run AUTO
PROGRAM, check the
results. Press the
CH(annel) +/– buttons on
your remote to cycle
through your available
channels. Or press the
PROG. LIST button to
show a list of the channels
and tune to them. See
page 28 in the Directions
for Use manual for more
on Program List.
c c C
HECK I T O UT
A
UTO
P
ROGRAM PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
H ELPFUL H INTS
• Philips strongly recom-
mends that you run Auto
Program. Otherwise, the
TV may not tune the chan-
nels properly, resulting in
improper pictures.
• If you change signal
sources—to a new cable
company or from antenna
to cable, for example—be
sure that Tuner Mode is
properly set for the new
source. Then run Auto
Program again. This will
ensure that the channels
are correctly stored in the
TV’s memory.
• If you have made
AutoLock™ settings,
remember that you must
remove any channel blocks
before Auto Program will
work.(See pages 46–54 in
the Directions for Use
manual.)
T UNER M ODE
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/
EXIT
VCR ACC
MENU/ SELECT
VOL CH
TV/VCR
ACTIVE
CONTROL
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
CABLE
ANTENNA
AUTO
1
5
2,3
4
CABLE
ANTENNA
AUTO
S et the TUNER MODE control according to the type of signal
you have connected to the TV—ANTENNA or CABLE. If you
select AUTO, the TV will automatically detect the type of signal
you have connected.
1 Press the MENU/SELECT button. The on-screen menu
appears. Press the CURSOR RING DOWN repeatedly until
INSTALL is highlighted.
2 Press the CURSOR RING RIGHT to enter the INSTALL
submenu. Then press the CURSOR RING DOWN once to
highlight TUNER MODE.
3 Press the CURSOR RING RIGHT to highlight the
TUNER MODE options list.
4 Press the CURSOR RING DOWN or UP repeatedly until
you select the option that matches your signal connection,
CABLE or ANTENNA. If you want the TV to determine
the type of signal, select AUTO. (You have selected an
option when the dot and triangle are next to the option.)
5 Press the STATUS/EXIT button to exit the menu.
6 Proceed to the section on “Auto Program.”
PICTURE
SOUND
FEATURES
INSTALL
LANGUAGE
TUNER MODE
AUTO PROGRAM
CHANNEL EDIT
AutoChron
H ELPFUL H INT
If you select the Tuner
Mode option that
matches your signal
source rather than
AUTO, the time
required for AUTO
PROGRAM to store
channels to the TV’s
memory may be
reduced.