Philips HP6475-00 User Manual

Important safety instructions, Danger, Warning

Advertising

ENGLISH

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical appliance, basic
precautions should always be followed, including
the following:

Read all instructions before using this
appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for an appliance that has

fallen into water. Unplug immediately.

2. Do not use appliance while bathing or in a

shower.

3. Do not place or store appliance where it

can fall or be pulled into a tub or sink. Do
not place or drop into water or other liquid.

4. Always unplug this appliance from the

electrical outlet immediately after using.

5. Unplug this appliance before cleaning.
6. Do not use an extension cord with this

appliance.

WARNING

To reduce the risk of burns, fire, electric
shock or injury to persons:

1. This appliance should never be used by, on,

or near children or invalids. Keep out of
reach of children.

2. Use this appliance for its intended

household use as described in this manual.
Do not use attachments not recommended
by Philips Electronics North America
Corporation.

3. Never operate this appliance if it has a

damaged cord or plug, if it is not working
properly, if it has been dropped or
damaged, or dropped into water. Return
the appliance to an Authorized Norelco
Service Location for examination and repair.

4. Keep the appliance, cord and plug away

from heated surfaces.

5. Never drop or insert any object into any

opening.

6. Do not use outdoors or operate where

aerosol (spray) products are being used or
where oxygen is being administered.

7. Never put the appliance in direct sunlight or

store in a pouch at a temperature above140ºF.

8. Always check rotating discs before use.

Do not use this epilator with damaged
or broken discs, as injury may occur.

9. Always check the shaving head foil before

use. Do not use if the foil or trimmer is
damaged, as injury may occur.

10. Always attach plug to appliance first, then

to outlet. Be certain that plug is inserted
firmly into appliance.To disconnect, slide
switch to OFF position, then remove plug
from outlet.

11. To prevent possible damage to the cord, do

not wrap cord around the appliance.

12. An appliance should never be left unattended

when plugged in.

13. When appliance is on, keep it away from

the hair on your head, eyelashes, eyebrows,
clothing, brushes, wires and cords to
prevent accidents, injury or damage.

14. If you have varicose veins, spots, moles or

blemishes, or your skin is sensitive or
irritated, or you have in-grown hairs or the
tendency towards producing in-grown hairs,
do not use this appliance.

15. This appliance is for dry use only.

SAVE THESE

INSTRUCTIONS

IMPORTANT: The power plug contains a
transformer. Do not cut off the power
plug to replace it with another plug, as
this will cause a hazardous condition.

Important

◗

Please read these instructions completely
before using this appliance.The following
information and precautions are important
when using the epilator.

◗

CAUTION: Methods of removing hair by
the root can cause ingrown hairs and minor
skin injuries. Please consult your doctor if
you have any questions about the use of the
appliance.

◗

Do not use the epilator if you suffer from
varicose veins, spots, moles or blemishes,
or when the skin is irritated, or if you have
in-grown hairs or the tendency towards
producing in-grown hairs. Consult your doctor
first.

◗

Use of the Satin Ice Epilator may cause
reddening or irritation of the skin.This is a
normal reaction, which should quickly
disappear. However, if irritation remains for
more than three days, consult your doctor.

◗

Any minor injury resulting from hair
removal may allow bacteria to
penetrate the injury site potentially
causing small scars or a change in
pigmentation of the skin.The risk of
infection may be minimized by
thoroughly cleaning the rotating
discs before and/or after each use
(see Cleaning section).

◗

The Epilator should only be used after
prior consultation with your doctor if you
have or experience:

- Open wounds
- Eczema, psoriasis (scaly eczema),

inflamed skin reactions such as folliculitis,
skin rashes or the tendency to allergy or
allergic reactions

- Body acne
- Immune deficiency or disorders
- Couperose, rosacea, or varicose veins
- Pregnancy
- Reduced skin immunity as results of

diabetes, pregnancy, Raynaud's disease, etc.

- Hemophilia
- If you have moles, raised skin bumps, etc.

◗

If you have been or begin taking hormone
medication, or have recently been pregnant, a
change in your hormone levels may
influence the thickness, color or amount
of hair growth.This is caused by the hormonal
changes, not by this method of hair removal.

◗

When removing hair from the area
behind knees, be sure to keep skin
stretched tightly to prevent pinching
of the skin by the rotating discs.

◗

When using the Epilator for the first time,
you may feel some discomfort, irritation
or experience reddening of the skin.This
is because the hairs are actually removed
at the root.The discomfort you feel will
tend to lessen with successive uses.You may
wish to remove hair in the evening so if any
reddening occurs it will diminish overnight.

◗

To help prevent ingrown hairs, it is
recommended to regularly exfoliate the legs at
least 2 days before epilating.

◗

Use only the cord provided.

◗

Clean appliance regularly following
Cleaning instructions.

Introduction

Congratulations! Your new Satin Ice Epilator
can remove unwanted hairs quickly, easily
and effectively.The combination of the proven
epilating disc system with the newly developed
skin cooler constitutes a revolution in epilation.
Thanks to the natural numbing effect of ice on
the skin, the new Satin Ice Epilator makes
epilation more comfortable. Even short hairs are
removed at the root by the quick rotating discs.
Any regrowth of hairs tends to be softer -
minimizing stubble.Your legs will stay silky smooth
and hair-free for weeks.To acquaint yourself with
how the Satin Ice Epilator works, be certain to
read the instructions and important information
contained in this booklet before using for the first
time. Satin Ice Epilator with the unique skin
cooler... the choice for smooth, silky results that
lasts for weeks!

Before Epilating

◗

Make sure your skin is clean, free from
grease and creams. Do not apply any
cream before using. Hairs are easier to
remove after a bath or shower; but your
skin should be completely dry before
using your Satin Ice Epilator.

◗

If you are using the appliance for the first
time, it is recommended that you begin at
an area with little hair growth to become
accustomed to using your Satin Ice Epilator.

◗

As the hairs are being removed by the
root, your skin may feel a little discomfort
after using the Satin Ice Epilator system
for the first time.This effect will gradually
lessen with each use.

◗

After epilation, regrowth of hairs tends to
be softer both in appearance and in touch.

◗

After each use, you may want to apply a
non-alcohol based mild cream or body
lotion which helps reduce the possibility
of skin irritation.

Freezing the Skin Cooler

Remove the protective sleeve from the
skin cooler (Fig. 1).

Put the skin cooler without the protective
sleeve in the freezer cassette and put it
in the freezer or freezing compartment
for at least 2 hours before you start
epilating (Fig. 2).

Make sure the outside of the skin cooler is
completely dry before you freeze it.

◗

Tip: You can store the skin cooler in the
freezer permanently.

Switch the appliance ON by selecting the
desired speed.

Depending on your skin type, Speed I or Speed II
may be used to exfoliate. We recommend you
start using Speed I and if a more intense
exfoliation is desired, use Speed II.

Place the exfoliating head onto your leg
and move the appliance slowly and
smoothly over the leg skin.

After exfoliating, you may apply cream or lotion
to the legs.

Cleaning

Do not use any corrosive detergents, scouring
pads or cloths, petrol, acetone etc to clean any
part of this appliance.

◗

Keep the appliance, plug and cord away
from water.

Cleaning the Epilator Head

◗

Never clean, remove or replace the epilator
head when the appliance is on.

◗

It is essential for hygienic reasons that the
epilator head is cleaned after each use.

◗

Do not apply pressure or touch rotating
disc with hard objects as this may dent or
damage the discs. If damage occurs,
discontinue use immediately.

Switch the appliance OFF by setting the
switch to ‘O’ and remove the plug from
the outlet (Fig 7).

Remove the skin cooler.

Slide the protective sleeve off the skin
cooler(Fig 3).

Clean the appliance, skin cooler and
protective sleeve with a moist cloth.

Clean the pivoting cooling head of the
skin cooler with a brush or moist cloth after
each use (Fig. 11).

Make sure the outside of the skin cooler is
completely dry before you put it in the provided
protective cassette. Return the protective
cassette, with the skin cooler inside, to the freezer.

Remove the epilating head. Press the
ribbed sections and slide the epilating head
off the appliance in the direction of the
arrow (Fig. 12).

Clean all accessible parts and the epilating
discs with the brush (Fig. 13).

Never try to detach the epilating discs from the
appliance.

Slide the epilating head back onto the
appliance against the direction of the
arrow (Fig.14).

The epilating head only fits onto the appliance in
one way.

Cleaning the Shaving Head

◗

Never clean, remove or replace the shaving
head when the appliance is on.

◗

The shaving head should be cleaned after
each use.

◗

It is recommended to replace the shaving
foil and cutter block once a year.

◗

Do not apply pressure or touch shaving
head with hard objects as this may dent or
damage foil or trimmers.

◗

Never use appliance with a damaged or
broken foil.

Make sure the appliance is switched Off
and unplugged.

Remove the shaving foil.

Clean the hair chamber and the cutter
block with the brush (Fig. 15).

To avoid damaging the shaving foil, do not exert
any pressure when cleaning.

For best shaving performance, it is
suggested to lightly oil shaving head
twice a year by spreading a drop of
mineral oil over the foil and the trimmers.

Replacement parts may be purchased on the
Norelco website, www.norelco.com

Cleaning the Exfoliating Head

◗

Never clean, remove or replace exfoliating
head when the appliance is On.

◗

It is essential for hygienic reasons that the
exfoliating head is cleaned after each use.

Make sure the appliance is turned Off
and unplugged.

Features

Remove the exfoliating head by moving it in
the direction of the arrow indicated on the
exfoliating head.

Clean the exfoliating head with the brush
while running under tap water (Fig. 16).

Storage

◗

Be sure appliance is turned off. Remove
cord from outlet and epilator before storing
in a safe, dry location where it will not be
crushed, banged or subject to damage.

◗

Do not wrap cord around the appliance
when storing.

◗

Store cord in a safe location where it will
not be cut or damaged.

◗

Do not keep appliance permanently
plugged into outlet.

◗

Do not place or store appliance where it
can fall or be pulled into a tub or sink,
water or other liquid while plugged in.

◗

Put the protective cap back on the shaving
head and exfoliating head after use.

◗

The appliance and the accessories can be
stored in the pouch.

◗

Put the skin cooler in the freezer cassette
and put this cassette in the freezer or in the
freezing compartment.

Assistance

For assistance or the Authorized Norelco Service
Location nearest you, call toll free:

1-800-243-3050
or visit our website: www.norelco.com

Authorized Norelco Service Location information
is available 24 hours a day, 7 days a week.

This appliance has no other user-serviceable
parts.Any other service should be performed by
an Authorized Norelco Service Location.

Accessories

◗

Replacement Shaving Foil
Model HP6116 - For maximum performance,
replace shaving foil once a year.

◗

Replacement Cutter Block
Model HP2911 - For maximum performance,
replace cutter block once a year.

◗

Replacement parts may be purchased on
our website, www.norelco.com

Full Two-Year Warranty

Philips Electronics North America Corporation warrants each new
Norelco product, Model HP6475, against defects in materials or
workmanship for a period of two years from the date of purchase, and
agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY A
NON-AUTHORIZED REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING
FROM WARRANTY SERVICE PERFORMED BY A NON-
AUTHORIZED REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply take or ship the product
postage prepaid to the nearest Authorized Norelco Service Location. It is
suggested that for your protection you return shipments of product by
insured mail, insurance prepaid. Damage occurring during shipment is not
covered by this warranty. NOTE: No other warranty, written or oral, is
authorized by Philips Electronics North America Corporation.This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the
above exclusion and limitations may not apply to you.
*Read enclosed instructions carefully.

Manufactured for:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation
1010 Washington Blvd., Stamford, CT 06912-0015

This symbol on the product’s nameplate means it is
listed by Underwriters Laboratories, Inc.

Norelco is a Registered Trademark of Philips Electronics
North America Corporation.
Satin Ice is a Trademark of Philips
Electronics North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke
Philips Electronics N.V.

Features

A Protective Sleeve for Skin Cooler
B

Leg Skin Cooler with Pivoting Cooling Head

C Freezer Cassette
D Epilating Head
E

Exfoliating Head Protective Cap

Exfoliating Head

G Shaving Head Protective Cap
H Shaving head
I

Appliance

Adapter

K Cleaning Brush

Storage Pouch
Full 2-Year Warranty
60-Day Money-Back Guarantee

Epilating the Legs

◗

To help prevent ingrown hairs, it is
recommended to regularly exfoliate the legs
at least 2 days before epilating.

◗

Make sure your skin is clean and free of
grease and cream. Do not use cream right
before you start epilating.

Remove skin cooler from freezer cassette.
Slide the protective sleeve onto the frozen
skin cooler (Fig. 3).

Occasionally the pivoting head freezes onto the
skin cooler.The pivoting head will start pivoting
again after you have passed it over your leg a few
times.

Snap the skin cooler onto the appliance
(Fig 4).

Put the plug into any 120V AC electrical
outlet.

Switch the appliance ON by selecting the
desired speed (Fig. 5).

◗

Speed I: for areas with little hair growth
and/or with bones directly beneath the skin
(such as knees and ankles).

◗

Speed II: for larger areas and/or areas with a
thicker hair growth.

Stretch your skin tight with your free
hand to make the hairs stand upright.

Place the appliance on the skin at a right
angle, with the cord pointing towards
you, and gently move it slowly over the
skin against the direction of hair growth
(Fig. 6).

Make sure both the epilating discs and the skin
cooler touch your skin.
Do not press the appliance onto the skin.

Be sure to stretch your leg when you
epilate the back of your knee.

Switch the appliance OFF by setting the
speed selector to position O (Fig 7).

◗

It is recommended that the epilator
be used on dry legs only.

◗

Note: If you choose to use a cream or
moisturizing lotion after use, be certain
it does not contain alcohol as it may
cause discomfort or irritation.

◗

IMPORTANT: After using the Satin Ice
Epilator some redness or irritation may
occur.This is normal and should
disappear quickly. Clean the appliance
regularly following CLEANING
instructions.

Shaving

◗

Use this epilator for its intended household
use as described in this manual.

◗

Use the shaving head to shave delicate
areas, such as your underarms and bikini line.

◗

Pressing too hard may cause skin irritation.

◗

Practice is best for optimum results.

◗

Make sure both trimmers and shaving foil
are in complete contact with skin.

◗

Do not use deodorant or alcohol-based
lotions immediately before or after shaving.
You may, however, want to use talcum powder.

Make sure the appliance is switched Off.

Remove the skin cooler from the appliance.

You can store the skin cooler in the freezer
permanently.

Remove the epilating head from the
appliance. Press the ribbed sections and
slide the epilating head off the appliance
in the direction of the arrow (Fig. 8).

Place the shaving head on the appliance
and move it against the direction of the
arrow indicated on the shaving head
until it snaps into place (Fig. 9).

The shaving head only fits onto the appliance in
one way.

Switch the appliance ON by selecting the
desired speed.

For best results, it is recommended to use Speed I.

Place the shaving head onto your skin and
move the appliance slowly and smoothly
against the direction of hair growth, while
pressing lightly.

Exfoliating

◗

Use the exfoliating head once or twice a
week to improve skin appearance. Only
exfoliate legs, not underarms or bikini area.

◗

Legs should be clean and dry before
exfoliating. Do not use cream, foam, gel
or lotion before or during exfoliating.

◗

For best skin appearance, exfoliate
before or within 2 days of epilating the legs.

◗

For hygienic reasons, make sure the
exfoliating head is used by only one person.

Make sure the appliance is turned Off.

Remove the skin cooler from the appliance.

Remove the epilating head from the
appliance. Press the ribbed sections and
slide the epilating head off the appliance
in the direction of the arrow (Fig. 8).

Place the exfoliating head on the appliance
and move it against the direction of the
arrow indicated on the exfoliating head
until it snaps into place (Fig. 10).

The exfoliating head only fits onto the appliance
in one way.

Satin Ice

60-DAY

MONEY-BACK

GUARANTEE

If you are not fully satisfied with your Norelco Satin
Ice product, send the product back and we’ll refund
you the full purchase price.
The product must be shipped prepaid by insured
mail, insurance prepaid, and have the sales
receipt, indicating purchase price and the date
of purchase, enclosed.The product must be
postmarked no later than 60 days after the date
of purchase. Norelco reserves the right to verify
the purchase price of the product and limit
refunds not to exceed suggested retail price.
Send dated sales receipt, your complete name and
address as indicated below, and the product,
prepaid to:

Philips Domestic Appliances

and Personal Care Company

A Division of Philips Electronics

North America Corporation

450 North Medinah Road, Dock 16

Roselle, IL 60172-2329

Please allow 4-6 weeks for delivery of check.

(Please Print)

Name_______________________________________

Address______________________________________

City_________________________________________

State ______________Zip_______________________

Daytime Telephone No. (______)________________

Email Address:_________________________________

REASON FOR RETURNING:

_______________

_______________________________________________

AREA CODE

HP6475

Epilator

7001327

4203 000 31971

SATIN ICE HP6475 NEW 1/17/06 12:15 PM Page 1 (Black plate)

Advertising

Popular Brands

Popular manuals